Model #30-1149-00-10 Tappan range (gas)

  • Cover Page
    3 Results
  • Backguard
    3 Results
  • Burner Parts
    3 Results
  • Body Parts
    3 Results
  • Cooktop And Broiler Drawer Parts
    3 Results
  • Door Parts
    3 Results

Question and Answers

Q:

I started my GE self clean oven at 10:00 and electric went off for just a second and came back on and it ran for 10 hrs and won't go off. GE oven

A:

Thank you for your question and I understand your concern.

The electronic oven control will display "F3" fault code when the oven temperature over heats or if the oven temperature sensor Ohm resistance exceeds 2900 Ohms. If leave the power supply off to the range and then re-connect the power and the oven begins to heat, the electronic oven control was likely damaged due to the electrical storm. Since I do not have model number I will not be able identify what type of door locking mechanism it may have or how you would access it. If you have the Owner's manual of the range, it should have one or more model numbers listed on it that would be helpful.

The range/oven will most likely need a new electronic oven control/clock assembly.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post along with the model number on the cover page of the Owner's manual.

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.


Read More
Joey S -
Sears Technician
April 12, 2013
Q:

kenmore microwave model # 363.62702200 is not working properly, acting strange.

A:

Thank you for your question.

By what you have stated I suspect there is problem with the unit control or a loose wire to the control. I have checked the price of a new unit control and it cost about $200.00. I recommend having the microwave serviced by trained service technician be cause of the dangers of repairing them. The microwave generates extremely high voltage. The capacitor can store this voltage even when the unit is unplugged. I hope you understand our policy on microwaves. Our number one concern is your safety. It is strongly recommended to have the microwave repaired by a service technician. You can have the microwave repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Depending on the age and the condition of the microwave, you may consider purchasing a new one. The price of microwaves has gone down a lot in the last few years. Please click on this link to view all of the microwaves we offer.

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 07, 2010
Q:

craftsman 10 hp 30 inch riding mower

A:

Thank you for your question on the engine of your mower not starting.

You have already done quite a bit of good troubleshooting so we will need to go deeper if you are comfortable with that.

It still sounds like you are not getting fuel into the cylinder even though you have cleaned the carburetor.

Without the model number of the engine or mower I cannot tell it you have an anti-backfire solenoid on the carburetor bowl. When you turn the ignition switch on you should be able to hear a slight click which would indicate that your carburetor has one.

When it clicks, it opens the fuel passage into the carburetor bowl and fills the carburetor.

Please reply with the model number of you tractor and we can continue to troubleshoot with that information.

Sam A.

Read More
Sam A -
Sears Technician
April 23, 2012
A:

Thank you for the update and the model number. This is a whole different model than I was thinking it was. I would first pull the spark plug and make sure the spark plug wire is not close to your hand and put you thumb over the hole to see if you have any compression when turning the engine over. If it blows your thumb off the hole then you may have enough compression. If it does not seem like it has a lot of compression then you may have a valve not closing. You may have to take the head off the engine to see if one of the valves is not closing when you turn the engine over. Please let me know what the engine brand and model number is and it could. Sam A.

Read More
Sam A -
Sears Technician
April 27, 2012
See more answers