Model #24A-424G063 TROYBILT Chipper Shredder/Vacuum, Gas

  • Upper Chipper Chute/shredder Hopper
    3 Results
  • Impeller/chipper Blade
    3 Results
  • Base Hitch/tongue Hitch
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a small tiller model #29270 and need to know which carberator it has. The site lists a 24a & a 24b. The lady at the 800# couldnt tell me which was needed

A:

Sometimes the manufacturers buy carburetors from more than one manufacturer. This creates problems when you want to overhaul the carburetor.

Most of the time the parts listing will list 24a as one brand of carburetor and 24b as a different brand.

Look on the carburetor to get the brand name and order the repair kit for that carburetor. The brand name of the carburetor is stamped on the body of the carburetor.

Read More
Jimmy K -
Sears Technician
April 29, 2010
Q:

Amperage /conflict info

A:

Thank you for your question and I understand your concern.

Based on the installation instructions, the dryer will require a three or four wire, single phase, 120/240 volt 30 amp service.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
November 29, 2013
A:

Jane: That is correct, it will need a 15 amp circuit breaker for each leg of voltage to the dryer. Two 15 amp breakes is 30 amps. The dryer requires 220 volts which is accomplish by connecting two different legs of voltage to the dryer. It needs line one (L1) and it needs a line 2 (L2). So, the dryer will need to be on 30 amp service. Two 15 amp circuit breakers, one of each leg of voltage.

Read More
Joey S -
Sears Technician
November 29, 2013
A:

Jane: I recommend contacting GE at 1-800-626-2005 and get the electrical requirement for your specific model dryer.

Read More
Joey S -
Sears Technician
November 29, 2013
See more answers
Q:

GJC3055RB02 - whirlpool electric cooktop glass top touch activated controls. The dual element on the rear right will not heat with just the small element on.

A:

Thank you for your question and I understand your concern.

The failure could be the electronic control board/appliance manager part #8286643, or it could have a faulty dual burner assembly key #24A part number 8285938, and slight possibility of faulty burner control module. A voltage measurement will need to be taken across the blue wire with a black strip at JP11 and the red wire at JP21 for 220 volts. Then across blue wire with a white stripe at JP10 and the red wire at JP21 for 220 volts when the control is set for both elements and then just the small one to determine if the electronic control is faulty or not. If you measure 220 volts across both, then I must assume the burner is faulty. See images in the second reply. I strongly suggest calling a service technician to diagnose and repair your cook top. It appears the unit will need to be un-installed in order to remove the glass top and/or the control box located in the right front bottom corner. NOTE: Disconnect the power supply from the cook top before servicing.

In order for the smaller element to come on, the control must close the relay for the smaller burner in order to complete the line one (L1) voltage supply to the smaller element.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 23, 2013
A:

Karen: I added a couple of images below to reference the circuit. I strongly suggest calling a service technician to diagnose the failure. The cook top appears it may need to be uninstalled to and flipped over or the glass top must be removed. The image shows a removable control box in the front right corner underneath the cook top. I do not have a service manual with instructions on how to access the control box.

Read More
Joey S -
Sears Technician
January 23, 2013
See more answers