Model #142 HUSQVARNA Chainsaw, Gas

  • Lever Link/chain Brake
    3 Results
  • Cylinder/piston
    3 Results
  • Air Cleaner/muffler
    3 Results
  • Clutch
    3 Results
  • Fan Housing/starter
    3 Results
  • Carburetor No. 530071987 Zama W-29
    3 Results
  • Bar/chain
    3 Results
  • Clutch Cover/lever & Link
    3 Results
  • Shield/cylinder
    3 Results
  • Muffler/carburetor/crankshaft
    3 Results
  • Chassis/clutch/oil Pickup
    3 Results
  • Fan Housing/eps Ignition
    3 Results
  • Carburetor #530071987-zama W-29
    3 Results
Find part by diagram >

Question and Answers

Q:

Craftsman lawn tractor 917270670: I am replacing return idler spring #169022 and extension spring 131335, please clarify if there are two springs

A:

Thank you for your question.

I am sorry you are having a problem installing the springs. I should be able to assist you with connecting the return springs. The deck has two springs that are the same. These springs are for the brake arms. The other spring is the idler arm return spring. I have posted an image below showing where the springs connect. Click on the image to enlarge it. The blue circles show the springs and the red lines show where they connect.

I hope this is helpful. If you need further assistance, please feel free to reply below with more details.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
October 03, 2011
A:


I will be happy to assist you. I posted an image below that shows where the idler return spring connects. Just click on the image to enlarge it. One end of the spring connects to the idler arm and the other hooks into a hole on the mower deck.

Please let me know if you need further assistance.
Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
August 13, 2012
See more answers
Q:

whirlpool duet ht-mod. ghw9400pw0 recently had a AC power surge on incoming power line (at 142 volt) now corrected have a code f-11 on washer will not reset

A:

The first link that Pvalde2 provided in the above response should give you some help in troubleshooting this failure. Here is another copy of that link: What is an F11 error code?

You can check for wiring connection problems as described in the above link (with the washer unplugged ).

Since you had a power surge, the Central Control Unit (also called Machine Control Board -- part 8182280) may need to be replaced. You could also have a bad Motor Control Board (part 8182706). I recommend that you check those control boards for burned spots. If a control board is apparently damaged, you can order a new one from the Sears PartsDirect website.

To avoid replacing unnecessary parts, I recommend that you have a service technician physically examine the washer if you find no apparent cause for the F11 code. Here is a link for the Sears Service website: Sears Home Services .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
January 06, 2011
Q:

I'm having burner issues with my stove

A:

I apologize for the errant advice that you received about replacing the clock timer on that range. You should be able to return that part based on the advice that you received. The clock timer in your range model 790.96021405 does not control the surface elements. Replacing that clock timer has no chance of fixing the burner problems that you are describing. The problem with the burner that heated constantly and would not turn off is likely caused by a failed infinite burner switch (part 5303935086). Replacing that burner switch should fix your problem on that surface element. The cause of the right rear burner not working could be a failed burner switch, a bad element or a wiring failure in that circuit.

I understand your concern about a recall on that range with a similar model number. Although that other range has a similar model number, it has a completely different control system for the surface burners. That other range that had the recall uses a circuit control board to regulate the surface burners. Your range uses basic infinite burner switches. That is why your range was not included in that recall.

That being said, I also understand your disappointment in the current Kenmore range that you have since you encountered these failures after only 5 years. Although a failure can occur at any time, that model of range is normally very dependable. Once you repair these burner problems, the range should work properly for many more years.

I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
November 08, 2012
A:

Hello Sue. I am sorry to hear that replacing the burner switch did not fix your problem. You could have a short in that burner circuit or a problem with the element. There is a chance that the wires were not connected properly to the new switch. I recommend that you have a service technician examine and repair the range. Since the breaker tripped, the wiring in the range will need to be examined.

Read More
Lyle W -
Sears Technician
November 13, 2012
A:

Hello Sue. I understand your concern and frustration with this failure. Since you are going to install a switch in that circuit again, I recommend that you check the condition of the wires. The first image below shows a wiring diagram for the right side burners. I highlighted the wires for the right side element circuits in that range. Be sure that you UNPLUG the range before accessing internal components. I recommend that you check the wiring that is highlighted in the image below. I tried to trace the wiring in actual wire colors. The second image shows how to lift the glass cooktop. You can lift the cooktop and check the elements and the wiring on those components using that information. I hope that this addition information helps. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
November 15, 2012
A:

Hello Sue. I am sorry to hear that the service technician could not complete that repair for you. If the service technician found no other problems with that circuit, then you may be able to replace that burner switch yourself. Be sure that the range remains unplugged when replacing that switch. If you need more help, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
December 03, 2012
A:

Hello Sue. We are glad to hear that the range is repaired. Thanks for the feedback regarding the repair by the service technician. I understand your concern regarding that service. I recommend that you call the Sears National Customer Relations at 1-800-549-4505 to get some help in resolving that issue. If you need more assistance, let us know. Thanks.

Read More
Lyle W -
Sears Technician
December 17, 2012
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show