Model #11098752793 Kenmore laundry centers/combos

  • Control Panel
    3 Results
  • Dryer Front Panel And Door
    3 Results
  • Dryer Cabinet And Motor
    3 Results
  • Dryer Bulkhead
    3 Results
  • Dryer Support And Washer
    3 Results
  • Washer Top And Lid
    3 Results
  • Washer Cabinet
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Tub And Basket
    3 Results
  • Washer Water System
    3 Results
  • Gearcase
    3 Results
  • Brake And Drive Tube
    3 Results
  • Product Accessory
    3 Results
  • Miscellaneous
    3 Results
  • 3402856 Burner Assembly
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Washer/Dryer Model #11098752793

A:

Thank you for your question and I understand your concern.

First; disconnect the power cord from the power supply.

To remove the top and front panel will require removing the diagonal panel from between the dryer and washer. After removing the diagonal panel; reach over the top of the washer and remove the screws from each of the hinges securing the top to the cabinet. Slide the top back until the front disengages from the two clips. Lift the top up at the front and then disconnect the lid switch and then place the top out of the way. After removing the top; remove the screws located at the top of each side panel securing front panel to the side panels. Tilt the top of the front panel towards you and then lift it up to disengage it from the two lower clips. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 03, 2012
Q:

Kenmore Washer/Dryer Model #11098752793; Washer Timer, Part #3952379 installation instructions

A:

Thank you for your question.

I will be happy to assist you with replacing the timer. The very first thing to do is to disconnect the power cord from the power source. Remove the timer knob by pushing the washer timer knob inwards and then rotate the knob counterclockwise (CCW) and then unthread the knob. Once the knob is removed you will see two hex head screws. Remove the two screws. Locate the screw at the bottom of the control panel at each end. Turn these screws located at the each end at the bottom edge of the control panel counterclockwise (CCW) but DO NOT thread the screws completely out. Turn them about 10 complete revolutions. After turning each screw about 10 revolutions, the top of the control panel should release and then can be tilted outwards to gain access to the timer and timer connections. Pull the timer quick-disconnect from the timer. Remove timer and reverse the procedure.

I hope this is helpful. Please let me know if you need further assistance.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 09, 2012
A:

Andrea after further investigation I found the images in the parts list are wrong. The timer in you model has a tab on the backside to release the knob. I have posted a link below that shows how to remove the timer. I am sorry for the wrong information before. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
January 19, 2012
A:

I am a little confused. Do you mean you are not sure how to install the dial on the timer shaft or you are not sure where to set the dial to start a cycle? If you are wondering about how to install the dial, it should only go on one way. The dial has a larger slot that matches the timer shaft. If you need information on where to set the timer, I will be able to help. I have posted a link below that will take you to the manual. Click on the link to open the manual. Once the manual is opened, you can save a copy to your computer and/or print out a copy. The manual has all the cycle information.

Read More
Mark T -
Sears Technician
March 07, 2012
A:

Andrea, when you install the dial it will only slide onto the shaft one-way. As long as the dial slides onto the shaft, you do not have to do anything else. Once you have the timer installed turn the knob until the line on the dial is aligned with the cycle you desire. In the manual on page 34 it shows the timer and on 36 it explains the cycles. If you have been using the washer you already know what cycles do what.

Read More
Mark T -
Sears Technician
March 11, 2012
A:

Thank you for your question. I am sorry that did not fix the washer. Without knowing all the details of what is going on with the washer, it is hard for me to recommend fixing or replacing it. If you would like I will be happy to assist you with diagnosing the washer. If you have a volt ohmmeter and feel confident making some live voltage checks, please reply below with the details of what the washer is doing. If you are getting a burning smell, try to pin point where it is coming from. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
March 22, 2012
A:

Andrea, Without a meter, it will be difficult to pin point the problem with the washer. I would hate to see you replace other non returnable parts, only to find that it did not cure the problem. I recommend calling out another technician to diagnose the problem. This time when they come out ask them to explain how the came to their diagnosis. I think we offer a coupon that will give you the cost of the service call off a new washer from Sears if you decide not to fix the washer. Just remember to ask if you set up the appointment. I have not been in the field for a few years so this might not be offered any longer. If you would like a Sears technician to come repair the washer please call 1-800-469-4663. Please let me know if you need further assistance.

Read More
Mark T -
Sears Technician
March 25, 2012
See more answers