Model #11095089402 KENMORE ELITE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8576353 Burner Assembly
    3 Results
  • Door Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

Dryer won't start. Panel lights up, but drum doesn't turn and no heat. 11095089402

Q:

Need help on installing new dryer belt Model # 110.95089402 11095089402 Kenmore Elite Residential dryer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.


REMOVING THE TOE PANEL
1. Remove two screws below the toe panel.
2. Slide the toe panel down, then pull it out
from the bottom.

ACCESSING & REMOVING THE ELECTRONIC ASSEMBLIES:
 
1. After locating the machine control
electronics, remove the three screws that
hold the machine control bracket in place
and remove assembly.

As you remove the assembly from its
mounting position, rotate the assembly
up to access the machine control circuit
board, and set it on the side panel.
Removing the Machine Control
Electronics
Remove all the wire connections to the
machine control board. 
There are two plastic legs on each side of
the circuit board that fasten it to the
mounting bracket. With pliers, squeeze the
leg while pulling up until it becomes
unlatched from the mounting bracket. Do this
at all four plastic legs, then lift the circuit
board from mounting bracket.
Accessing the Console Electronics
and Housing
1. After locating the machine control
electronics, disconnect the ribbon cables
that run between the console and the
machine control board. Make the
disconnection at the machine control
side. Remove the two screws that fasten
the console assembly to dryer. Then
remove the console assembly, sliding it
up and off from the front of the machine

2. Remove the screws that fasten the
console mounting bracket onto the
assembly. Lift up and remove the bracket
to locate the electronics assembly.
3. The console electronics and housing
assembly is held to the decorative piece
by seven plastic latches.
4. Unlatch them gently with a screwdriver
while pulling the electronics housing
assembly out. 
5. Gently pull the console electronics
housing away from the decorative piece.

REMOVING THE BACK PANEL
After removing the top panel, remove the
cover plate. Then remove ten screws from
the back panel, plus two screws on the back
panel’s top edge, which connect the back
panel to the side panels’ top edges. See
figure 24.
ELECTRIC DRYER:In addition to the
above, remove the ground wire and screw
from back panel. Also disconnect the power
cord from the terminal block, and then
remove the terminal block from the back
panel.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 20, 2015
Q:

Dryer is not producing heat

A:

I'm sorry that you are having some difficulties with your Kenmore Dryer. I did a little research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
June 03, 2011
A:

A blown thermal fuse is a common failure that will prevent this type of dryer from heating. The image below shows how to remove the bottom front service panel to access that component. Be sure that you unplug the dryer before accessing internal components. You may also need to remove the lint screen and the lint duct to access the thermal fuse on the blower housing. Once you access that fuse, you can test it using the procedure shown in this short video: Thermal Fuse Testing . If that fuse is blown then you can order a new one from the Sears PartsDirect website. The part number is 3392519.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

NOTE: If that fuse was blown, be sure that you check the exhaust vent duct system for a clog or restriction as shown in that video. Also wash that lint screen using water and a soft bristle brush to remove fabric softener residue.

If the thermal fuse is okay, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
June 04, 2011
A:

I have a Kenmore Elite dryer model# 11095089402...it is operating but suddenly stopped producing heat. Any suggestions as to which ?

Read More
Mario Lopez -
July 16, 2013
A:

Mario Lopez: The first component to disconnect and test is the thermal fuse. The thermal fuse will have two red wires attached. Disconnect the power cord from the power source and then remove the two screws above the front lower access panel. Look for the blower wheel housing and on top you will see the thermal fuse with two red wires attached. Disconnect the red wires and test the thermal fuse for continuity with an Ohm meter. If it does not measure continuity, replace the thermal fuse. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
July 17, 2013
A:

i checked the thermal fuse with meter it beeped i checked high limit thermostat blue red wire it beeped checked all connections i pluged back in worked than it didnt unpluged again worked than it didnt any advice please

Read More
orlando -
July 08, 2015
See more answers

Top Parts