Model #11088732793 KENMORE laundry centers/combos

  • Control Panel
    3 Results
  • Dryer Front Panel And Door
    3 Results
  • Dryer Cabinet And Motor
    3 Results
  • Dryer Bulkhead
    3 Results
  • Dryer Support And Washer
    3 Results
  • Washer Top And Lid
    3 Results
  • Washer Cabinet
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Tub And Basket
    3 Results
  • Washer Water System
    3 Results
  • Gearcase
    3 Results
  • Brake And Drive Tube
    3 Results
  • Product Accessory
    3 Results
  • Miscellaneous
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

KENMORE ALL IN ONE WASHER #110-88732793

A:

Hi Joan,

Thank you for submitting a question to Manage My Life.

I am including the disassembly instructions for this type of laundry center in the images below. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
February 02, 2012
Q:

When I load my 120v stackable dryer, the heat is barely warm thus causing very long drying time. Why, and is it normal?

A:

Thank you for your question.

  • The operation of the your dyer is normal.

  • The 1400 watt element can only run on 120 volts on this model, so it is going to only feel warm,and it will take twice as long to dry the clothes, as a standard 240 volt dryer.

  • A regular dryer with, lets say a 5000 watt 240 volt element is more of what you may be use to.

  • If you do not have 240 volt circuit available at your location, this model is the option for being able to have a washer and dryer.

I hope this will answer your question.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
September 08, 2010
Q:

Laundry center 11088732793, water won't go into the washer.

A:

Hi Robert,

Thank you for submitting a question to Manage My Life. I am sorry you are having problems with your Laundry center.

To start you need to gain access to the water level switch. I have included two documents below that will demonstrate disassembly procedures on 2 types of laundry centers. One of these should be similar to yours. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

Disconnect the violet and pink wires from the water level switch. Tape the violet and pink wires together with electrical tape and make sure they will not touch anything else. Plug your Laundry center back in and start a cycle. If water starts coming in stop the cycle and unplug your Laundry center. This indicates a bad water level switch. Do not leave the water level switch bypassed, this is for testing only.

If no water starts coming in you likely have a bad timer. You will need to check voltage at that point. . If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you in any way I can.

Here is a link that you may use for parts purchases Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Please perform the diagnostic tests detailed here and report back with your findings. I am looking forward to assisting you again in the near future.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
June 21, 2011

Top Parts