Model #11082983110 KENMORE residential washers

  • Top And Cabinet
    3 Results
  • Console Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness Parts
    3 Results
  • Water System
    3 Results
  • Gearcase
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Taking the Motor/tranny/clutch off of model 11082983110.

A:

Thank you for your question.

I should be able to help you with replacing the clutch in the washer. First, unplug the washer and remove the cabinet. I have provided you with the instructions for removing the cabinet. Next, you have to remove the agitator. To remove the agitator you have to remove the agitator cap. Then remove the bolt in the center and lift the whole agitator out of the washer. Next, you have to move below to the pump. Remove the clips from the pump and slide it off the motor shaft. Doing it this way you do not have to disconnect the hoses and leak water all over. At this point, I recommend removing the motor because it makes the gear case easier to lift. To remove the motor release the clips securing the motor and the harness. Once the motor is out of the way, pull the washer out from the wall a few feet and tip it back against the wall. If you have anyone around, have him or her hold the washer against the wall. Then remove the three bolts holding the gear case. Please make sure to hold the gear case up while removing bolt so that it does not fall. Once all of the bolts are removed, slide the assembly out of the washer. The third image below shows how to replace the clutch. After you have the new clutch in reassemble the washer in the reverse order.

I have found a video that show how to replace the clutch. Please click on this link to watch the video .

Please let me know if you need further assistance on repairing the washer.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
February 17, 2011
Q:

Replace coupler

A:

Hello,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your washer.

Here is a video that will demonstrate the best way to replace the motor coupler on your washer; Video . Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

Here is a link that you may use to purchase the Motor Coupler for your washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
June 01, 2011
Q:

Washer keeps filling

A:

Thank you for your question and I understand your concern.

Based on your symptom and details; the water inlet valve on the washer is faulty and will need to be replaced. The water inlet valve is available and the part number is 285805. Replacing the water inlet valve is an easy do it yourself project. The valve can be ordered from SearsPartsDirect . I added a YouTube video showing how to access and replace the water inlet valve. NOTE: Disconnect the power cord from the power source before placing the control panel in the service position.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 16, 2011

Top Parts