Model #11082673110 Kenmore residential washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Miscellaneous
    3 Results
  • Console Panel
    3 Results
  • Machine Base
    3 Results
  • Retainer Clips & Wiring Harness
    3 Results
  • Water System
    3 Results
  • Brake Clutch, Gearcase, Motor And Pump
    3 Results
  • Gearcase
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Model 11082673110 not spinning

A:

Thank you for your question and I understand your concern.

If the motor is running in the drain and spin cycles and the motor coupler is not broken, the failure is likely in the gear case or a worn out clutch assembly. If you start the washer in a spin cycle and then open the lid and let the motor come to a full stop and then shut the lid, the transmission should shift into spin. If the basket does not attempt to spin at all even with help, then it's likely a gear case failure. Now, when the washer is in the spin cycle, the clutch housing/assembly located above the gear case should be spinning. If you find the clutch housing spinning, then it could have worn clutch or the basket drive tube is seized inside the tub support. If the clutch housing is not spinning then it will likely need a new gear case. The gear case can be disassembled and possibly be repaired.

In order to access the clutch in order to see if it's spinning or not when the washer is in the spin cycle will require removing the washer cabinet and jumping out the lid switch.

I added images below to reference if needed.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
May 02, 2013
Q:

kenmore washer series 70 model 11082673110

A:

Thank you for your question and I understand your concern.

If the motor runs in the drain and spin cycles, the lid switch is okay, timer and the wire harness. If will run in the agitate cycles but not in the drain and spin cycles, it very well could be the lid switch. If the motor is overheating and shutting off on the motor thermal overload, the motor is most likely faulty. If the motor is laboring due to a friction issue, it will overheat and shut off.

The wiring diagram John provided in his first response does show the wire colors and where the wires terminate at the motor. If the motor is overheating, and there is nothing causing a high amount of friction to the motor, the motor is likely bad. If the motor is running for a short time during the drain and spin before it over heats, make sure it is draining all the water before it shifts into spin. If the motor centrifugal switch contacts BK and R do not open once the motor starts, it will cause the motor to overheat and shut down on the thermal motor overload.

 

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
November 04, 2013
A:

al machiaverna: If the motor is overheating and shutting off when the motor is connected and sitting on the floor, the motor is faulty. You know the motor is getting voltage if it will start and run. The centrifugal switch on the motor should have letters indicating the switch terminals. There should be a red wire leading from the capacitor to the terminal R, terminal BK will be a black wire. If you have to spin the motor shaft to get the motor running, then its not likely getting the start voltage to start the motor or it has fault capacitor. If the motor will start on its own, and then overheats, it will be a faulty motor. The white wire on the motor is the neutral, leave one meter lead there at all times and then place the other voltage meter lead on blue for high speed and orange is the low speed voltage supplies. Look at the wiring diagram in the previous response from the first tech helping you. If you do not have experience and feel safe and confident in making votlage measurements, please call a service technician to diagnose and repair the washer.

Read More
Joey S -
Sears Technician
November 04, 2013
A:

al machiaverna: Replace the motor. It is worn out and seizing up.

Read More
Joey S -
Sears Technician
November 04, 2013
A:

al machiaverna: Thank you for the complement. Have a great day!

Read More
Joey S -
Sears Technician
November 04, 2013
See more answers
Q:

What is the capacity of Kenmore washer model 11082673110 and gas dryer model 11087681100?

A:

The washer is a 3 cu. ft. model. The dryer is 6 cu. ft.

Read More
Lyle W -
Sears Technician