Model #11078532700 KENMORE Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8318272 Burner Assembly, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:



Question and Answers


broken motor?? 11078532700


Thank you for your inquiry on your Kenmore Washer, Model: 110.78532700. From reviewing the details on your model, I have found a video which basically trouble shoot the motor and explains the process to figure out if its good or bad. I have included the link below.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the dryer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663

I hope this answered your question. Thank you for contacting, and have yourself a wonderful day. 

Read More
Gerry93 -
Sears Technician
February 24, 2015

gas burner 11078532700 Kenmore Residential dryer


Thank You for contacting I do apologize for the delay in answering your question.

I understand your frustration when your dryer doesn't want to work. Before replacing the entire burner assembly I would check to make sure you have good air flow and the vents are not clogged. Remove the vent off the back and start the dryer. The temperature of the air coming out of the back should be between 115 to 150 degrees. If the dryer runs great with the vent removed then you have an air flow issue.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Gas Burner Assembly for Model 11078532700 

If you need further assistance please respond below. Thanks for visiting

Read More
Desirea -
Sears Technician
March 31, 2014

Gas Dryer Heating Problem 110.78532700


Thank you for the inquiry and for using I am sorry to hear about the gas ignition issue you are experiencing on the dryer, I know how frustrating that is.

A gas dryer works by blowing air through a burner assembly which heats the air, using a gas valve, ignitor and a flame sensor. Within the ignitor are ignition coils that function to take energy from the ignitor and channel it into opening the gas valve so the gas can flow through.

The first and easiest thing to start with would be to make sure the exhaust hose/vent is free and clear of any lint clogs. This includes the lint duct of the dryer, the lint screen, the hose, and the vent leading outside. If you have a clog anywhere in the exhaust of the dryer, it will prematurely cut out the heat because having air flow is critical in the burner operation.

If the exhaust venting checks out, I would check the ignition coils. Weak gas valves will normally be strong enough to open on the initial ignition when they are cold. After they are heated up, they will fail on subsequent ignition attempts.

Sometimes the ignition coils in gas dryers can go bad. If you suspect you have this problem, test it by checking the ignitor when the dryer is on. If the ignitor glows for several seconds when powered up, then goes out, the problem is probably the ignition coil. Use a multitester to test the coil for resistance. The multitester should change from a reading of infinity to roughly 1,300 ohms when applied to the coil. If the reading stays at infinity or is substantially different from 1,300 ohms, it is an indication the coils need to be replaced.

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, click here to be directed to the page to set up service.

I wish you all the best with the diagnosis and repair for the dryer. If you have any further questions or inquiries, please don't hesitate to ask. Thank you for using

Read More
Jeff Wallace Sr -
Sears Technician
August 12, 2013

Top Parts