Model #11067732794 Kenmore residential dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore dryer model 11067732794

A:

Thank you for your question and I understand your concern.

First, is the dryer getting the proper voltage supply of 220-240 volts? Is one of the two house circuit breakers tripped?

When measuring voltage across the two wires connected to the heating element, it must measure 220-240 volts or the dryer will not heat. Each one of the wires connected to the heating element should measure 110-120 volts to ground/neutral when the wire is disconnected from the heating element. When you measure across the two wires it will measure 220-240 volts. The heating element must have 220-240 supplied to heating element or the heating element will get hot.

I added an image in a second reply of the wiring diagram. I traced the heating circuit in red. Each one of the components connected in the heating circuits must be closed in order to complete the path of voltage to the leads of the heating element.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 18, 2013
A:

Brett: I added the wiring diagram in the image below. I traced the heating circuit in red. Each on of the components connected in the circuit must be closed in order to complete the two lines of voltage to the heating element. I would use an Ohm meter and disconnect the wire from the component and test the component for continuity.

Read More
Joey S -
Sears Technician
January 18, 2013
See more answers
Q:

Dryer running, but not heating

A:

Hi Mario,

Thank you for submitting a question to Manage My Life.

If you are sure that the heater and both thermostats are OK, then this issue could be caused by the thermal cut off, timer, wiring, or motor (centrifugal switch). I am including a wiring diagram below. I have marked these for you in green. You may also have a problem with the house electrical supply. I assume you have a meter, so I have included the information you need for testing the outlet below. Ohm the TCO and the remaining checks will require live voltage checks. If you are comfortable making live voltage checks and are confident in your technical abilities, please reply below and I will be happy to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Landell

Read More
Landell -
Sears Technician
November 01, 2011
Q:

Dryer stopped working mid cycle 11067732794 Kenmore Electric dryer

A:

Thank you for your question and I understand your concern.

Based on your symptom and details, if the house circuit breaker dedicated for the dryer has not tripped and the dryer is getting the proper voltage supply of 220 volts, I suspect the thermal fuse has failed.

The thermal fuse is located on the blower wheel housing behind the dryer. The thermal fuse will have two (2) blue wires connected to it. The thermal fuse can be disconnected and tested for continuity with an Ohm meter. If the thermal fuse does not measure continuity, the thermal fuse is bad. The thermal fuse for Kenmore dryer model 110.67732794 is part #3392519 which can be ordered from Searspartsdirect.

Disconnect the power cord from the power source before removing the vent hose and rear panel.  

I added an image below of the wiring diagram showing the thermal fuse connected in a series circuit with the motor. I also added an image with the thermal fuse circled in red.

 This may be the issue. If not, please reply and I will be glad to assist you further. 

 

Read More
Joey S -
Sears Technician
June 01, 2013