Model #11067087600 Kenmore Elite residential dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results

Question and Answers

Q:

fuse size for a oasis dryer with an F 40 code

A:

Hi Mike,

Thank you for submitting a question to Manage My Life.

Here is a link to a previous question on a similar dryer with the same issue; Kenmore Oasis Electric Dryer Model #110.67092600 I was trying to dry on the Normal setting the dryer powers on but is giving me a F40 error. . Follow the troubleshooting I included in my answer to this question.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details in a reply to this post.

Landell

Read More
Landell -
Sears Technician
February 22, 2012
Q:

COMPATABLE REPLACEMENT PARTS OASIS DRYER ELECTRIC CONTROL PANEL

A:

Thank you for your question and I understand your concern.

Based on your symptom and details, either one of the buttons is sticking or it has a faulty User Interface board.

Our parts system calls for part #8564396. The number you found on the User Interface #8564400 will work if it's worked in the past. You see an image of part #8564400 here .

I was not able to find or confirm part #8564382.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 10, 2013
A:

Amy; I added an image below of the procedure for replacing the user interface. Be sure to disconnect the power cord from the power source before servicing.

Read More
Joey S -
Sears Technician
January 13, 2013
See more answers
Q:

My Kenmore Elite Oasis dryer stopped working and flashing code F40.

A:

I apologize for all of the trouble that you have had while addressing this issue. I will do my best to help you get this situation resolved.

The F40 does indicate that you have a communication error between the main machine control board and the control board that governs the blower motor in the bottom of this dryer. This is sometimes caused by a failed control board but often it can be caused by a loose wiring connection as described in that link for a previous answer that Alina F. posted in the above response. It can also be caused by a blown thermal fuse. This is probably the most frequent cause of the F40. I recommend that you check that issue first. The first image below shows a diagram of the components in this dryer. The second image shows how to open the cabinet and access the thermal fuse. Be sure that you unplug the dryer before accessing internal components. The third image shows a wiring diagram with the wires going through the thermal fuse and then to the motor control board highlighted in blue. Here is a brief video that shows how to check that thermal fuse using a volt/ohm meter: Video: Thermal Fuse Testing . (If you don't have a volt/ohm meter, you can normally buy one at your local Sears store or hardware store for around $20 or less.) This information should help you check that issue. If that thermal fuse is blown, it will need to be replaced. The part number for that thermal fuse is 3390719. NOTE: Check the exhaust vent duct system for a clog as shown in that video if the thermal fuse was blown .

If that thermal fuse is okay, I recommend that conduct the tests shown in the 4th image below for that blower motor (with the dryer still unplugged ). A problem with that blower motor can cause the F40 code. One other problem that can cause the F40 code is an internal wire harness fuse in that wiring that is highlighted in blue on the third image below. If the above tips don't help you find the cause of the F40, I recommend that you check the continuity in that wiring between the P9-1 connector on the main machine control board (blue wire) and the MC1-4 connector on the motor control board (black wire). Be sure that you still have the dryer unplugged during this test. The resistance through that wiring should be near zero ohms (continuity) if the thermal fuse is okay. If it is open (measures infinite resistance or ol -- Open Load) then that wiring harness will need to be replaced.

I provided the access information for the control boards in the 5th image even though you probably already have that since you replaced that control board.

This may be a large amount of technical information to digest. If you have any questions or need more help, reply with additional details and we will assist you further.

I appreciate your feedback regarding the problems that you had with our service. I will pass that along to our managers. I hope that we can make this right. I am confident that we can. If a control board was not needed for this repair, I am sure that we can arrange for you to return that component.

Read More
Lyle W -
Sears Technician
August 13, 2011
A:

Here are the 4th and 5th images.

Read More
Lyle W -
Sears Technician
August 13, 2011
See more answers