Model #11067042600 KENMORE ELITE residential dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts, Optional Parts (not Included)
    3 Results

Question and Answers

Q:

Why is the door not closing on my Kenmore dryer?

A:

There is a door strike on top of the front panel just outside the door opening that pushes into a door catch on the door to keep it shut. If the door catch is bent or broken, then the door will not stay shut properly. Since the door is reversible, there is a catch on both sides of the door. If the catch is broken, you can replace it with the one from the opposite side.

If the hinges are loose, the door may not be lined up properly so that the door strike enters the door catch properly.

These tips may help you resolve your door problem. If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
Q:

Why does my Kenmore dryer model 11067042600 clash CF 01, 02, 03 and now won't turn on?

A:

The CF 01, 02 and 03 cycling indicates that the DRYNESS LEVEL button is probably stuck or that you have a failed user interface control board. The normal procedure for adjusting Preset Dryness Level Settings by holding the DRYNESS LEVEL button down for 5 seconds and then changing the setting from 01 to another setting is explained on page 22 of your owner's manual. Since the dryer cycles through this option on its own, then it is likely that you will need to replace the user interface control board to fix this problem. The procedure for replacing this control board is provided in this link of a previous answer: Why is my Kenmore Oasis dryer showing the code F2?

You can order a new user interface control board from the Sears PartsDirect website. The part number is 8564377.

Read More
Lyle W -
Sears Technician
Q:

KENMORE ELITE, Model # 11067042600 My dryer stopped heating but still tumbles, please help.

A:

Thank you for your question and I understand your concern.

There could be one of several possible component failures preventing your dryer from heating providing the dryer is getting the proper voltage supply. If the voltage supply is correct, then it could have a heating element failure, an open thermal cut-off or an open high limit thermostat. In order to access the heating element, thermal cut-off and high limit thermostat will require removing the front panel. See images below for instructions. Note: Disconnect the power cord before servicing your dryer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

The first thing to check is the two house circuit breakers dedicated for the dryer. Locate the two dedicated circuit breakers and reset both breakers by flipping them OFF and ON 2-3 times and then restart the dryer and check for heat. If it continues to run and not heat then the next step is to check and confirm the voltage supply at the dryer where the power cord attaches. The voltage must measure 220-230 volts when measuring across the two out side terminals. NOTE: I do not recommend checking voltage unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose and repair your dryer.

I added a YouTube video showing how to test the thermal cut off which is used to check the continuity of the heating element and high-limit.

Read More
Joey S -
Sears Technician
April 16, 2011
A:

Wes: Yes, disconnect the wires from the component before testing it for continuity. I added an image below that will have troubleshooting information. The model number Justin submitted above does not have a dual element. You can look up the part number and price at Sears Parts Direct.com. for your specific model dryer. Here is a YouTube video showing how to test the heater. http://www.youtube.com/watch?v=wq-3zsiBID8&feature=player_embedded

Read More
Joey S -
Sears Technician
November 07, 2011
A:

Wes: You are welcome and I'm glad you were able to get heating again. Thanks for using Manage My Life.

Read More
Joey S -
Sears Technician
November 07, 2011
See more answers

Top Parts