Model #11066722694 Kenmore residential dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Model 110-66722694 Dryer Parts list

A:

Thank you for your question.

I have checked and we do not have the parts list offered as a down load. You can click on the following link to view the parts of your dryer. once you have the image opened you can print the exploded image.

Dryer parts

Please let me know if you have problems looking up any of the parts.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
October 22, 2010
Q:

My Kenmore 70 Series Electirc Dryer Model # 11066722694 dry's well but it won't stop running

A:

Thank you for your question and I understand your concern.

I'm not perfectly clear in understanding if the timer is advancing through the cycles but will not advance all the way to the off position or if the timer is not advancing at all.

If the timer is not advancing at all when using the "Automatic" dry cycle or it advances all the way through the auto cycle but fails to advance one or two clicks before it reaches the off position, the failure is likely a faulty resistor which is connected in series between terminal OR (orange wire) on the timer and terminal on the high limit thermostat. See image below.

The resistor can be disconnected and tested for resistance with an ohm meter. It must measure 5000 ohms in order to be okay. NOTE: Disconnect the power cord from the power source before accessing and testing the 5000 ohm resistor.

If the timer is not advancing when set on "Time" dry, the timer is likely faulty and will need to be replaced. Parts can be ordered from Sears PartsDirect

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 01, 2011
A:

Alex: Why was the timer replaced? What is the part number of the new timer? Is the timer not advancing at all or it advances up until it almost reaches the Off postion? Is it Time or Auto dry? Please add additional details so I have a better understanding of the exact symtom. If the timer is not advacing at all, it could have faulty timer or broken wire. The timer motor voltage supply can be measured across timer terminals BK and TM when on time dry and then across BK and OR when in the automatic dry. When the timer is in tht auto dry, voltage will only be present across BK and OR when the operating thermostat is satisfied/when the burner cycles off.

Read More
Joey S -
Sears Technician
August 01, 2013
A:

Alex: The timer motor will only have voltage and run in the automatic cycle after the dryer reaches operating temperature and the operating thermostat opens to shut off the burner. You will not see the timer advance for at least 3-4 heating cycles of the burner. If you place the voltage meter leads across terminals BK and TM when in auto dry, you should measure 120 volts when the burner cycles OFF. In time dry, there should be a constant 120 volt measurement across BK and TM. I added an image of the wiring diagram if needed.

Read More
Joey S -
Sears Technician
August 02, 2013
A:

Alex: When measuring the votlage across the timer motor leads, 120 volts will only be measured when the dryer is running and after the burner shuts off when the timer is set to auto dry. If you measuring 120 volts in time dry and the timer is not consistently advancing, the timer is most likely faulty. If you measure 120 across the timer motor leads, the timer should eventually advance after a few minutes of running. It only advances one increment at time.

Read More
Joey S -
Sears Technician
August 05, 2013
A:

Alex; If the dryer is not producing heat, the timer will not advance in the auto dry cycles. The dryer may have lost the proper voltage supply. The dryer needs 220 volts in order for the heating element to work. The heating element nees line one voltage and line two voltage. If the dryer is getting 220 volts, it could have a broken heating elements, faulty thermal cut-off or it could be timer issue. I added the wiring diagram in a couple of my replies to use so you see the heating circuit.

Read More
Joey S -
Sears Technician
August 13, 2013
See more answers
Q:

kenmore dryer model #11066722694, will not keep running after releasing start switch.

A:

Thank you for your question and I understand your concern.

Based on your symptom contact 5M and 6M are not closing once the motor starts. These contacts are inside the motor centrifugal switch. Another thing that could cause your symptom is if there is a break in the wire connected to 6M and where it splices or connects to black and blue wires. I traced the circuit in question in yellow in the image below.

When the contacts inside the motor centrifugal switch closes 5M to 6M it completes the neutral circuit to the motor so it continues to run after releasing the start switch. You could disconnect the wires from terminals 5M and 6M and measure across the two terminals with an Ohm meter. You will have to activate the centrifugal switch to the run position before checking for continuity. You should see a plastic disc that slides back and forth on the motor shaft with a couple of small springs. The normal position is start. You will have to manually push the plastic disc over to close contact 5M to 6M. If it does not measure continuity, the motor will need to be replaced. NOTE: Be sure to disconnect the power cord from the power source before servicing the dryer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 27, 2012