Model #11062802101 KENMORE residential dryer

  • Top And Console
    3 Results
  • Cabinet
    3 Results
  • Bulkhead
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore 80 series Model 110-62802-101

A:

Thank you for your question.

I see that Alina F has given you a link to an answered question. Most of the time when a dryer is heating but not drying it is because of a plugged vent. I recommend following the instructions in the link.

If you need further assistance, please reply below.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
November 15, 2010
Q:

how do I connect my Kenmore 11062802101 power cord

A:

Thank you for submitting a question to Manage My Life.

Here is a video that demonstrates replacing the power cord on a dryer similar to yours; Video . The installation guide that Anna gave you above shows this as well. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. The dryer in this video may not look exactly like yours but the procedure is basically the same.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

Here is a link that you may use to view the parts list diagram or purchase any parts needed for your appliance; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please include more details in a reply to this post.

Landell

Read More
Landell -
Sears Technician
May 30, 2012
Q:

My dryer is making a loude sound when it runs.

A:

Thank you for your question.

From your description of the noise you are hearing it could be a couple of areas in the dryer that could cause this noise.

  • The most likely cause would be the drive belt idler pulley bearing.

• The other possible cause is the drum support roller bearings.

Let us address the easiest one to repair first.

• To replace the belt idler pulley I recommend the replacing the belt also.

• The Idler part number is: 691366.

• The Belt part number is: 341241.

You can purchase these parts from Sears Parts Direct .

To install these parts you will need to access the inside of the cabinet. And it will require a few basic tools. A ¼ inch nut driver, a Phillips # 2 screwdriver, a 5/16 nut driver.

• REMOVE POWER to the dryer.

• Remove the lint filter from the dryer.

• Locate and remove the two screws that hold the dryer vent assembly to the dryer top. (Be careful not to loose the screws down the filter vent hole).

• To remove the top for the dryer insert a putty knife about 2 to 3 inches from either side of the cabinet where the top and the front panel meet. Push in on the clip and lift up on the top cabinet to release. Do this on both sides. Raise the top and lean back.

• Locate and remove the screws securing the side panels to the front panel at the top of the inside cabinet. Locate and remove the door switch connector from the wire harness.

• Remove the screws from the bottom of the cabinet and pull up to lift off the cabinet from the retaining clips on the side walls of the cabinet. Set front panel to the side.

• Remove the back panel from the back of the dryer.

• Locate the drive belt tensioning system in the cabinet next to the motor and remove the belt.

• At this point you should be able to lift the dryer drum out of the cabinet.

• This will help you to gain access to the tensioner and replace with the new roller style.

• Re-install the belt onto the dryer drum and install drum into the dryer cabinet making sure you get the back of the drum positioned onto the drum support rollers into the groove on the drum.

• Re-install the belt onto the dryer belt tensioner. (I will send a picture to make sure you install correctly.

• At this point re-install the cabinet parts and panels and make sure the drum is correctly positioned onto the front drum support felt seal and re-install mounting screws.

• Re-install the top and filter vent screws.

• Re-connect power to the dryer and test run.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I hope this helped with this repair.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
August 31, 2010

Top Parts