Model #11062202101 Kenmore residential dryer

  • Cabinet
    3 Results
  • Top And Console
    3 Results
  • Bulkhead
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Dryer will not turn off 11062202101

A:

Thank you for your question and I understand your concern.

I must assume the heating element is cycling on and off.  

The little timer motor on the timer which advances the timer operates on 220 volts.  The timer contacts TM and WB or timer contacts TM and OR must close in order to complete the line 2 (L2) voltage supply to the timer motor in order for the timer to advance to off.  One of the two (TM and OR) or (TM and WB) must close in order to advance the timer from cool down to off. I added an image below of the wiring diagram and traced the timer motor circuit in red and black. The red is the line 2 voltage supply. The timer motor must have 220 volts in order to advance. You will also see an Orange wire connected between the high limit and one side of the heating element to terminal OR on the timer. Make sure this orange wire is not open or disconnected. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
March 26, 2013
A:

RIchard: Paste the URL below in your browser and then you will be able to access the image. http://www.managemylife.com/mmh/questions/339134-kenmore-dryer-turn-11062202101

Read More
Joey S -
Sears Technician
March 26, 2013
See more answers
Q:

Kenmore Dryer Model #11062202101 will not start

A:

Hi Shari,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

I sent you a wiring diagram in my response to your previous question.

If you are sure that you have the start switch and the door switch wired correctly, you probably have a bad thermal fuse. There is a way to check the thermal fuse. Unplug the dryer and gain access to the fuse. Here is a video that will demonstrate gaining access to the Thermal Fuse . Remove the blue wires and tape them together with electrical tape (be sure this will not touch anything). Plug the dryer back in and try starting a cycle. If the dryer starts, replace the thermal fuse (part number 3392519). If your dryer will not start you need to check the wiring of the PTS (push to start switch) and door switch. Do not leave these wires taped together, this is for testing purposes only.

The remaining checks will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you in any way I can.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
September 01, 2011
Q:

Dryer runs, blows air, doesnt heat up 11062202101 Kenmore Dryer

A:

There is a possibility that a voltage supply problem is preventing the dryer from heating. The dryer will run if only one of the 120 volt legs of 240 volt power is supplied to the dryer. If that second 120 volt leg of power is missing, the dryer won't heat. I recommend that you check the house circuit breakers. You should have a double breaker for the dryer. Shut the breakers off and then reset them. See if the dryer heats. If not, you can carefully check the voltage supply at the dryer electrical outlet as shown in this brief video: Video: Perform a Voltage Check on a 240 Volt Outlet .

If the outlet voltage is okay, then you could have a bad component or a wiring failure in that heating circuit. The wiring diagram in the first image below shows that heating circuit traced in red. The bright red shows the L1 side of the circuit and the dark red traces the L2 side of the heater circuit. You indicated that you already replace the heater element and the high limit thermostat. You can unplug the dryer and check the thermal cut-off fuse and the operating thermostat for continuity using a volt/ohm meter. The location of the components on the back of the dryer is shown in the second image. Those components should measure about zero ohms of resistance (continuity). If a component measures OL -- open load or infinite resistance, then it will need to be replaced. You can order parts from this page: Kenmore Dryer Model 110.62202101 Parts . Be sure that you unplug the dryer before accessing internal components and replacing parts.

I hope that this additional information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 13, 2012