Model #11047532600 Kenmore residential washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Tub And Basket Parts, Optional Parts (not Included)
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

11047532600 how do i put the boot on?

A:

Hi Paul,

Thank you for submitting a question to Manage My Life.

Here is a video on a similar washer that demonstrates this procedure; Video . Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. The washer in this video may not look exactly like yours but the procedure is basically the same.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

Here is a link that you may use to view the parts list diagram or purchase any parts needed for your appliance; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here and if I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
April 30, 2012
Q:

washer stops working, screen has F - 20, works if I unplug and plug it back again, what a hassle. Can you please help me. tnx..

A:

Thank you for your question and I understand your concern.

The washer will stop operating and "F20" fault code will display if the water level pressure switch is not tripped after 6 minutes of filling with water. If the water is entering too slowly, "F6" will display. Based on your details, either the hot or cold water is most likely entering too slowly. I recommend turning the water supply off and removing the hot and cold fill hoses from the back of the washer. Place the end of the hoses into a mop bucket and then turn the hot and cold water back on and check to see if the water is flowing slowly. If the water is flowing out the fill hose with force and volume then shut the water off and then look up inside the fitting where the hoses were connected for any debris in the filter screens. If the screens are clear of any restrictions or debris and the water is entering slowly, the water inlet valve on the washer will need to be removed and replaced.

If the water entering the tub is coming in normally then the other possible failure is the water level pressure switch (key#23). The water level pressure switch and the water inlet valve are accessed by removing the top panel. NOTE: Disconnect the power cord from the powers source before removing the top.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 01, 2011
Q:

my washer is not completing wash cycle, f-25 is flahing in window and the fabric softner dispencer in retaining water.

A:

Hi Patricia,

         

Thank you for submitting a question to Manage My Life.

         

The F25 error code indicates the control is unable to detect motor speed. The first link above is a previous answer that I gave on a washer similar to yours with the same problem. This can be a difficult issue to diagnose.

         

First, I would advise you to check to spin bearings for wear. To do this, grasp the basket and while turning it apply pressure in an up and down fashion as you turn it. If the bearings are worn you should feel resistance or grinding. If you do notice resistance or grinding the bearings (part of the rear outer tub) will need to be replaced.

         

The remaining checks will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you further.

         

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

         

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

         

I hope this is helpful. If I may be of further assistance please reply to this post.

         

Landell

Read More
Landell -
Sears Technician
February 15, 2012