Model #11045976400 Kenmore Elite residential washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Pump And Motor Parts, Optional Parts (not Included)
    3 Results
  • Pedestal Parts (not Included) (for 13`` Pedestals Only
    3 Results
  • Pedestal Parts (not Included) (for 15 1/2`` Pedestals
    3 Results

Question and Answers

Q:

front load washer 11045976400 HE 3T

A:

That F6 code indicates that the control detects a drive motor tachometer (speed sensor) error. Here is a link for a previous answer that provides detailed technical troubleshooting for that problem: kenmore washer he3t

If you get to a point where you need to have a service technician diagnose and repair this problem, the you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
April 19, 2012
Q:

model # 11045976400 washed rug then machine would not spin or drain how to troubleshoot

A:

Hi Jennifer,

Thank you for submitting a question to Manage My Life.

The first thing you will need to do is check the drain pump filter. I am including images below that will show you how to gain access to this filter. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

Make sure it is not clogged with debris from the rug. Put your washer back together and then try a cycle.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details in a reply to this post.

Landell

Read More
Landell -
Sears Technician
March 07, 2012
Q:

Why is the rubber lining coming out of my HE3 washer as well as a metal ring?

A:

It is possible that you can repair this problem yourself. If the rubber door boot is not damaged, you can just reattach it properly to the washer. If it is damaged, it will of course need to be replaced. You can order a new door boot from the Sears PartsDirect website. The part number is 8182119. It costs $98.50 not including tax, shipping and handling.

If the boot and spring clamp are just detached from the door opening, you can likely use the parts of the procedure in the images below to reattach the boot and this may fix your problem. The spring clamp will take significant force to reposition on the lip of the door opening with the door boot in place. The usual method of replacing it is to position the spring clamp at the 12 o'clock position and work the spring clamp into the lip starting at the bottom and working upward. You will need to stretch the clamp outward as you work your way up the opening evenly on both sides. I recommend that you wear gloves when performing this process.

The images below show how to access and replace the door boot (bellows) on this type of washer. Your washer may look slightly different than the one shown below but the basic procedure will be the same. Be sure to unplug the washer before accessing internal components. If the door boot is damaged or is detached from the tub, you will need to use this entire procedure. The basic process involves these steps:

  • Unplug the washer.
  • Remove the top washer panel.
  • Remove the bottom front service panel.
  • Remove the dispenser drawer.
  • Pull the spring clamp off.
  • Push the door boot into the tub.
  • Disconnect the wires from the door lock assembly or remove the door lock assembly from the front panel.
  • Remove the console.
  • Remove the front washer panel.
This process will give you access to the clamp that secures the door boot to the washer tub. Reattach the door boot or replace it using the tips in the third image to make sure that it is properly positioned and secured. Reverse the process for reassembly.

This is not an easy repair but with the information provided you may be able to complete it yourself. If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
July 24, 2009