Model #11042924200 KENMORE ELITE Residential Washers

  • Top And Cabinet
    3 Results
  • Door And Latch
    3 Results
  • Control Panel
    3 Results
  • Dispenser
    3 Results
  • Tub And Basket
    3 Results
  • Pump And Motor
    3 Results
  • Pedestal Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

HE3T washer 11042924200

A:

That amount of detergent is safe for that type of washer. It should not cause any problems. I have not heard of any problems with those pods. I have not used them myself but I will try them. I will reply to this thread with the results that I encounter.

Read More
Lyle W -
Sears Technician
April 19, 2012
A:

I got a chance to use that pod detergent. It worked fine in my front load washer. I had no problems.

Read More
Lyle W -
Sears Technician
May 10, 2012
See more answers
Q:

Washer CU FT?

A:

Thank you for your question.

I have checked the model number you have submitted and your model is a 3.7 cubic foot model.

If you need further assistance, please reply below with more details.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
November 07, 2010
Q:

How do I replace the bellows seal on my Kenmore washer?

A:

Here are the steps for replacing the bellows on your washer:

NOTE: Metal edges of the washer can be sharp. Use care when working near these exposed edges. Use of protective gloves is recommended.

  1. Unplug the washer or completely disconnect electrical power.
  2. Turn off the water supply to the washer.
  3. Remove the top cover of the washer. Three screws secure the washer top at the back of the washer. Remove the three screws and lift the top from the washer.
  4. Remove the console from the cabinet. Disconnect the Touch Pad/LED Assembly ribbon connector from the left side of the Central Control Unit and release it from the wiring harness brackets on the right side of the washer top. Remove the detergent dispenser drawer by pressing down on the release tab at the back of the drawer and pulling it completely out of the washer. Once the drawer is removed, remove the screw in the recessed hole next to the drawer opening. Release the tab securing the right side of the console to the washer and remove the console. Be sure the ribbon cable clears the cabinet frame.
  5. Remove the front of the bellows from the front panel of the washer. Use a flat bladed screwdriver at the location of the retainer spring and pull the retainer forward and then off the perimeter of the boot. Ease the edge of the boot off the front panel of the washer. Push the bellows inward once the outside edge is removed from the front panel.
  6. Remove the door switch assembly from the front panel. It is secured by 3 screws. Remove the screws and lift slightly up and pull back to release it from the front panel.
  7. Remove the screws securing the toe panel to the front of the washer and remove the toe panel by lifting slightly and pulling forward (see image).
  8. Remove the two screws securing the bottom of the front panel to the washer, and the two screws securing the top of the front panel to the washer. The front panel can now be removed from the washer (see image).
  9. The boot can be completely removed from the outer rim of the tub assembly. Carefully pull the boot from around the water inlet and window washer tubes. Remove the boot retainer clamp by loosening the clamp screw located at the upper right of the tub opening. The boot can now be removed from the tub.
  10. When replacing the boot and washer front panel, special care must be taken to assure a proper water seal and operation. Carefully pull the nozzle from the window washer tube. Separate the plastic gasket ring from the nozzle. Insert the nozzle through the hole in the boot and slide the plastic gasket ring down the shaft of the nozzle so that the boot is securely trapped between the gasket ring and the nozzle ridge. Insert the nozzle shaft into the window washer inlet tube and insert the end of the water inlet tube into the boot.
  11. Fit the boot around the front lip of the tub so it rests smoothly and evenly (see image for proper fitting). Fit the boot clamp around the front lip of the tub and tighten the screw. Be careful not to over tighten this screw. Damage to the boot clamp or the boot could occur. Also, under tightening will cause the bellows to slip off or leak. To prevent over tightening, use a nut driver or screw driver with a straight handle instead of a wrench or a ratchet. If you have a torque wrench, tighten the screw to between 9 and 12 in. lbs. of torque.
  12. When reinstalling the door switch, be sure to insert the two tabs on the right side of the switch assembly into the slots in the plastic wiring harness guide. Failure to do this will result in unwanted noise while the machine operates.
  13. Continue with the reassembly of the washer in reverse order.

Read More
Lyle W -
Sears Technician
April 28, 2008

Top Parts