Model #11029622801 Kenmore residential washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts, Optional Parts (not Included)
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore washer model 11029622801, was cleaning dispenser and a triangle looking part came off.

A:

Hi Serena,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your washer.

I am not sure which part you are talking about. If you could send a picture of that part I will be happy to try and help you further.

Here is a link to the Parts list diagram for your washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
July 21, 2011
Q:

my kenmore washer stops after wash cycle & i have 2 click it 2 the next cycle why?

A:

Since the washer continues after you manually advance the timer, it is almost certainly the timer (part 8577356) that is causing this failure. You can probably fix this problem yourself by replacing the timer.

You can order a new timer from the Sears PartsDirect website. Here is a direct link for that timer: Timer .

To replace the timer, unplug the washer and open the console as shown in the image below. Your washer will look slightly different than the one shown below but the procedure is the same.

To remove the knob from your existing timer, push the knob in and then hold the slotted rod end on the back of the timer stationary with a small screw driver while you pull the knob off of the shaft. Replace the timer and reassemble the washer.

If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 28, 2011
A:

Based on your description, replacing the timer (part 8577356) should fix this problem. You can order the new timer from the Sears PartsDirect link provided in the above response. UNPLUG the washer. Open the console. Follow the tips for removing the knob from the timer. Once you remove the knob and the skirt from the front of the console, you can remove the screws that secure the timer in the console. Transfer the wires to the new timer and install it in the console. This information should help you complete the repair. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 31, 2011
A:

For Tracy: This type of washer will normally display an error code when it stops in the cycle and will not spin. If you did not notice an error code, you can run the diagnostic test shown in the first image below. You should see one of the error codes shown in the 2nd or 3rd image. If your console does not have a digital display, then the error codes will be displayed as shown in the 4th image. You may see the F21 (Long Drain) error code. Check for excessive suds. If you see excessive suds, you will need to drastically cut back on the amount of HE (High Efficiency) detergent that you are using. You should only need about 1 tablespoon of detergent per load. A problem with the drain could also cause the F21. Make sure that the washer drain is working properly. Check the drain hose for a kink or clog. If necessary, you can UPLUG the washer and remove the bottom service panel as shown in the 5th image. If you need to manually unlock the washer door, you can carefully reach up along the inside of the front panel and pull down on a manual release tab at the bottom of the door lock assembly to unlock the door. Drain the water out of the washer using a wet/dry shop vacuum. Place a shallow pan (baking pan) under the pump clean-out filter and remove that component. You may find a clog in the drain pump. These tips may help you with this washer problem. If you need more assistance, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
February 03, 2011
A:

For Tracy: Here are the 4th and 5th images.

Read More
Lyle W -
Sears Technician
February 03, 2011
A:

For Mike: After reading this last reply, it appears that you may be describing the Extra-Rinse cycle and not the normal rinse cycle. If this is the case, then I recommend that you make sure that the Extra-Rinse switch is turned on. If it is on and the washer is not advancing into the extra rinse cycle, then I recommend that you UNPLUG the washer and tape the wires that go to the Extra-Rinse switch together with electrical tape to bypass that fuse. Reassemble the washer and see if it will go into the extra rinse cycle with this switch bypassed. If it does then replacing the Extra-Rinse switch (part W10168262) should fix your problem. If the washer is still not advancing to the regular rinse cycle then you may still have a problem with the timer. You may need to have a service technician examine the washer in this situation. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
February 07, 2011
A:

The timer dial should only fit one way on the shaft. It should not have to be lined up. Once it is properly installed, the timer dial should be aligned properly. You may need to have a service technician physically examine the timer to resolve this problem.

Read More
Lyle W -
Sears Technician
February 07, 2011
See more answers
Q:

my kenmore washing maching will not stop dripping into the tub.

A:

Thank you for your question and I understand your concern.

The constant dripping of water into the tub is caused by a faulty water inlet valve. Replace the water inlet valve to resolve the dripping water. The vacuum break with thermistor and both hot and cold solenoids will be all one assembly. The part number is W10144820 and can be ordered from SearsParstDirect .

I added a YouTube video showing how to remove the cabinet in order to access the vacuum break with solenoids. The video is directed at replacing the motor but of course you will not need to go that far. The video shows how to release your console at the 54 second mark.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 26, 2011