Model #11028522701 Kenmore residential washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts, Optional Parts (not Included)
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore 11028522701 Wont spin in the spin cycle.

A:

Your symptoms point to a timer problem. When the washer gets to the final spin portion of the cycle, the motor will drive the drain pump for a minute or two without the basket spinning. The timer should pause the drive motor for moment after this process to set the spin mechanism. When the drive motor restarts, the basket should spin. Your details seem to indicate that the basket will not spin until the washer stops. Once it stops, you can reset the timer to spin and the basket will rotate properly. This indicates that the timer is not pausing the drive motor properly at the first of the spin cycle after that drain process is completed. That is why I recommend that you replace the timer to fix this problem. You can order that timer from the Sears PartsDirect website. The part number for the timer is 8577356. Here is a direct link for that part: Timer .

The image below shows how to replace that timer. The washer in that image is slightly different than yours but the basic procedure is the same. Be sure that you unplug the washer before accessing internal components.

These tips should help you fix this washer problem based on your details. If you need more help, reply with additional information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
October 05, 2011
Q:

is there a reset switch 11028522701 Kenmore Residential washer

A:

Thank you for your question and I understand your concern.

There is not a reset switch on the washer. The problem with your washer is most likely a broken lid switch. If the lid is open or if the lid switch fails, the washer will not operate except for adding water. The lid switch is located under the control panel oven on the left side. When the lid is shut, the left hinge must strike the lid switch actuator in order to close the contacts in the switch to complete the nuetral path to the motor. The lid switch could be okay and the left hinge arm may not be pushing on the lid switch actuator enough to close the contacts in the lid switch too.

If you find a faulty lid switch, the part number of the lid switch for Kenmore washer model 110.28522701 is 8318084 which can be ordered from Searspartsdirect.co.

 

Read More
Joey S -
Sears Technician
October 16, 2013
A:

John; I'm glad peace is back in the village. I'm happy I was able to help. Have a great day.

Read More
Joey S -
Sears Technician
October 16, 2013
See more answers
Q:

washer repair

A:

Thank you for your question and I understand your concern.

I would have to assume the extra rinse switch is either set to the extra rinse position or the extra rinse switch is faulty. If you do not ever use the extra rinse option you could disconnect one of the two wires connected to the extra rinse switch and it should prevent the washer from filling at the end of the cycle and going through extra rinse cycle. The extra rinse switch is part #W10168262 which can be ordered from Sears PartsDirect .

To access the switch you will need to place the control panel in the service position. There is spring clip located under the front area of the left and right end caps. Slip a putty knife up under the front of the end cap and push inwards and pry up. NOTE: Disconnect the power cord from the power supply before placing the control panel in the service position. To remove the extra rinse switch, pry the locking tap away from the bracket and rotate the switch in order to disengage it from the bracket.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
September 07, 2011