Model #11027642600 Kenmore residential washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts, Optional Parts (not Included)
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My 11027642600 Kenmore Washer rattles badly at end of spin cycle. Why?

A:

Thank you for your question.

I am sorry you are having a problem with the washer. By the symptoms you are having I suspect the problem is a defective drive block. When the drive block loosens up the washer will spin fine but as soon as the motor stops the washer will make a loud thumping or banging noise until the basket stops. Depending on how long this has been going on you might need to replace the basket drive also. I have found a video that shows how to replace the drive block. Click here to watch the video. Once the drive block is removed look at the ears on the tube sticking up. If the ears on the tube are rounded, the basket drive should be replaced also. To replace the basket drive you will need to remove the transmission. Click here to watch a video on how to remove the transmission. Once it is out turn the plastic part that hangs down, to release the brake and removes the drive.

The parts for the washer can be ordered from our parts website: Sears Parts Direct .

I hope this is helpful. Please let me know if you need further assistance on the washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 31, 2012
Q:

How can I remove soap scum build-up from basket/tub of washing machine (Kenmore Model 11027642600)?

A:

I can understand wanting to clean the scum building on the inner wall of the outer tub. In order to access this area will require removing the washer cabinet and tub cover. NOTE: Disconnect the power cord from the power source before servicing your washer.

I added an image below with the instructions on how to remove the washer cabinet. Note: The image of the console will look different than yours but the procedure is the same. Once you have the washer cabinet taken off, remove the tub cover by prying all the locking tabs outwards and then lift the tub cover off. You now have access to the scum. I recommend using a flat plastic ruler to scrap the scum off and then wipe the inner tub clean.

Read More
Joey S -
Sears Technician
October 26, 2010
Q:

Replacing Washer Drain Hose?

A:

Thank you for your question.

I am sorry you are having a problem with the washer. I will be able to help you with replacing the drain hose. First, unplug the washer. Then you will need to remove the cabinet. I have added the instructions for removing the cabinet below. Now place a few towels down on the floor under the pump because some water will come out when the hose is removed. Once it disconnected from the pump you can remove it from the back of the washer. There are just tabs to release the plastic holder. Then reassemble the washer in the reverse order.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
June 23, 2011