Model #11026002010 Kenmore residential washers

  • Top And Cabinet Parts
    3 Results
  • Console And Dispenser Parts
    3 Results
  • Basket And Tub Parts
    3 Results
  • Gearcase, Motor And Pump Parts
    3 Results
  • Optional Parts (not Included)
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Washer Model #11026002010

A:

I added some images below that show the actuator and splutch assembly on that washer. Based on your details, you may have a bad actuator and a damaged splutch assembly. I recommend that you unplug the washer and examine those components. You can order parts from this page: Kenmore Washer Model 110.26002010 Parts .

If you need help diagnosing the washer or determining which parts to replace, reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 31, 2013
A:

Here are the images.

Read More
Lyle W -
Sears Technician
January 31, 2013
A:

The intermittent problems that you are describing could be caused by loose wiring connections or a problem with the electronic control board. Reply with the model number of your washer and we should be able to help you with some troubleshooting tips.

Read More
Lyle W -
Sears Technician
February 12, 2013
See more answers
Q:

kenmore washing machine model#11026002010

A:

Hi Kelley,

Thank you for submitting a question to Manage My Life.

This washer does make different noises than the older style top load washers we are accustomed to. But without hearing the noise you are talking about, it is hard for me to determine if it is normal. Make sure the sound shield was installed. You will have to tilt your washer back to look for the sound shield. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. I am including an image below that describes the sound shield installation. There are not any fasteners used to hold the sound shield, it simply sits on top of the base frame.

If you do not feel confident resolving this issue yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
December 06, 2011
Q:

Not spinning. 11026002010 Kenmore Automatic washer

A:

The actuator shifts the drive system between the agitation mode and the spin mode. If that actuator gets stuck or breaks, then the washer will fail to agitate and/or spin.

 

The blinking lid light indicates that the control detected a problem. I recommend that you recall the fault code as described in this link for a previous answer: http://www.managemylife.com/mmh/questions/352015-kenmore-top-loader-washer-11026002010-cycle-correctly-unit-cycle-lights-door-lock-light-blinks-unit-performing-cycle-indicated?page=1&per_page=20  .

 

The fault code normally leads you in the direction of your failure. You can order parts from this page: Kenmore Washer 110.26002010 Repair Parts.  That previous answer provided above shows how to access components in the washer. Unplug the washer before accessing internal components and replacing parts.

 

If you need more help, reply with additional details and we will assist you further. 

Read More
Lyle W -
Sears Technician
November 06, 2013
A:

Hello Debbie. I posted an image on the above thread that shows how to read error codes on models that don't have a digital display. The code is displayed in the diagnostic test mode using the status lights as shown in that document that I posted. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
November 11, 2013
See more answers