Model #11022932100 KENMORE Residential Washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Tub size on 11022932100

A:

That washer has 3.2 cu. ft. of capacity.

Read More
Lyle W -
Sears Technician
April 17, 2012
Q:

Do I need a new belt if my Kenmore washer motor runs but won't agitate or spin?

A:

Your washer is considered a direct drive washer which means it does not use a belt. It uses a motor coupler to connect the motor to the gear case. In order to access the motor coupler will require removing the washer cabinet.

  • First, disconnect the power cord from the power source.

  • The console (key#26) will need to be placed in the service position by removing two (2) hidden screws, one (1) screw is located at the bottom of the left hand end cap (key#7) and one (1) screw is located at the bottom of the right hand end cap (key#10).

  • In order to access the two (2) hidden screws, the left hand end cap trim (key#8) and the right hand end cap trim (key#15) will need to be removed.

  • To remove the end cap trim (key#8&15), place you finger behind the trim at the very top and bend it up enough to clear the console and then hinge it towards the front and off.

  • Remove the hidden screw under each end cap trim at the bottom of the end caps. Slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

  • Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) gold colored cabinet clips off as shown in the image below.

  • Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

  • Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

  • Remove the water pump by prying the two (2) pump retainer clips off.

  • Leave the two (2) pump hoses connected to the pump and shove the pump over to the left and out of the way of the motor.

  • Disconnect the motor wire harness plug from the motor.

  • Pry the two (2) motor retainer clips off. Note: if there is a screw threaded through the motor retainer clips, remove the screws before prying the motor retainer clips off.

  • Remove the motor.

You now have access to the motor coupler. The motor coupler consists of three (3) parts. One fits on the gear case input shaft, one fits on the motor shaft and the rubber isolator links the two together once the motor is reinstalled.

See images below for further instructions. Part number of the motor coupler is 285753A. I added a link to Sears Parts Direct with the part looked up for you. Click on "Coupler" to open the link.

Reverse the procedure to re-assemble the washer.

Read More
Joey S -
Sears Technician
May 07, 2009
Q:

Why are my clothes still wet after spinning?

A:

The burning that you smell could be coming from the motor coupler. I recommend starting a new cycle and checking to see if the washer will agitate. If the motor hums but the washer will not agitate or spin, then it is likely that your motor coupler is broken (see images).

A technician is normally needed to complete this type of repair.

If your washer does agitate, you could have a clutch or basket drive problem. Resubmit your question with additional details if you need more help with this washer problem.

Read More
Lyle W -
Sears Technician
April 04, 2008

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show