Model #11022642100 Kenmore residential washers

  • Top And Cabinet
    3 Results
  • Control Panel
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Won't run 11022642100

A:

A failed lid switch will prevent the washer from draining and spinning. It will not prevent the washer from agitating. If the motor won't run in the agitation mode, then you could have a problem with the drive motor, the wiring or the timer.  I recommend that you have a service technician diagnose and repair that type of failure. Here is a link for service: Sears Homer Services Washer Repair.

 

If you need more help, reply with additional details and we will assist you further. 

Read More
Lyle W -
Sears Technician
November 06, 2013
Q:

Kenmore model 110-22642100

A:

Hi Johnny,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

Leaking issues are hard for me to diagnose without being there to see the washer for myself. The most likely cause of this issue is a leaking tub seal (part number 383727). Here is a video that will demonstrate gaining access to and replacing the tub seal; Video . Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. This video is for demonstration purposes only. This washer may not look exactly like yours, but the procedure is basically the same.

Once you have the cabinet removed, you will need to look for evidence of the leak to determine the area of interest.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
September 11, 2011
A:

Hi Johnny, You are welcome. Glad I could help. Below is a link that you may use to purchase the Spanner Wrench for less than $10.00. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
September 11, 2011
A:

Johnny, Glad to hear you are back in business. Please keep Manage My Life in mind for all of your do-it-yourself projects. Landell

Read More
Landell -
Sears Technician
October 16, 2011
See more answers
Q:

How to fix spin cycle on washer 110-22642100

A:

Thank you for your question and I understand your concern.

If the motor is running and the washer will not agitate or spin but will drain, the motor coupler is likely broken. You model does not have a drive belt but uses a motor coupler to connect the motor shaft to the gear case shaft.

In order to access and replace the motor coupler will require removing the washer cabinet from the base.

  • First, disconnect the power cord from the power source.

  • The console will need to be placed in the service position by removing two hidden screws, one screw located at the bottom of the left hand end cap and one screw located at the bottom of the right hand end cap.

  • In order to access the two (2) hidden screws, the left hand end cap cover and the right hand end cap cover will need to be removed.

  • To remove the end cap covers, place you finger behind the trim at the very top and bend it up enough to clear the console and then hinge it towards the front and off.

  • Remove the hidden screw under each end cap trim at the bottom of the end caps. Slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

  • Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) gold colored cabinet clips off as shown in the image below.

  • Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

  • Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

  • Remove the water pump by prying the two pump retainer clips off.

  • Leave the two pump hoses connected to the pump and shove the pump over to the left and out of the way of the motor.

  • Disconnect the motor wire harness plug from the motor.

  • Pry the two (2) motor retainer clips off. Note: if there is a screw threaded through the motor retainer clips, remove the screws before prying the motor retainer clips off.

  • Remove the motor.

You now have access to the motor coupler. The motor coupler consists of three (3) parts. One fits on the gear case input shaft, one fits on the motor shaft and the rubber isolator links the two together once the motor is reinstalled.

The motor coupler #285753A can be ordered from Sears Parts Direct.

See images below for further instructions.

Reverse the procedure to re-assemble the washer.

Read More
Joey S -
Sears Technician
November 14, 2012

Recommended maintenance parts & accessories

Show 3 more
No more item to show