Model #11022062101 Kenmore Elite residential washers

  • Top And Lid
    3 Results
  • Cabinet And Frame
    3 Results
  • Washplate, Basket And Tub
    3 Results
  • Control Panel
    3 Results
  • Brake, Motor And Pump
    3 Results
  • Suspension
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube
    3 Results

Question and Answers

Q:

Washer 11022062101 replace or repair?

A:

 

Thank you for your question and I understand your concern.

I recommend replacing the washer rather than having it repaired because you could run into an issue just getting the u-joint assembly off. The cost of repair could increase tremendously if the u-joint is seized to the drive shaft.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


 

Read More
Joey S -
Sears Technician
February 20, 2013
Q:

Washer Calypso model 11022062101 wouldn't drain not is very noisy.

A:

Hi Chon,

Thank you for submitting a question to Manage My Life.

I know how frustrating it can be when appliances do not function properly.

I assume the washer is draining now. You did not indicate where the noise you are talking about is coming from. The noise you are hearing during agitation could be coming from the leveler. The leveler acts as the mechanism that tilts the nutator or outer wash plate from level to a 35 degree tilted position. The leveler is driven by the nutate shaft which replaces the traditional agitator shaft. A shifting mechanism on the underside of the leveler moves it from a perpendicular alignment in the spin mode to the 35 degree tilt required for nutation. In the spin mode, the top of the leveler is positioned to be in line with the nutate shaft. This levels the outer wash plate so that the spin basket spins without an out of balance condition that would be caused by a tilted wash plate. The leveler shift mechanism is moved from nutate to spin by the nutate shaft direction and an interference with the inner wash plate embossment.

The Drive Motor operates the nutate and spin functions by reversing direction. The Drive Motor is linked to the drive mechanisms by a stretch belt. The belt transfers the motion of the Drive Motor to a Drive Pulley. The Drive Pulley has a splined hub, into which the Nutate Shaft is inserted and is in motion in whichever direction the Drive Pulley is turning. The Drive Pulley, Drive Motor and Drive Belt all turn in a clock-wise direction, as viewed from underneath when the system is Nutating. The Drive Motor reverses direction for Spin and causes the Drive Pulley to turn in a counterclockwise direction, as viewed from underneath. When turning in this direction, an actuating bump in the hub of the Drive Pulley will contact the Brake Release pawl on the Spin Tube/Brake assembly. This releases the brakes and allows the basket to spin.

It would be helpful to know where the noise is coming from. Is it just under the basket or is it coming from the lower end?

This washer is controlled by an electronic control rather than a timer. If the washer is not advancing it should be giving an error code that will indicate a failure. I have included an image below that will guide you through the diagnostics on this washer. Run the diagnostics and see if the unit will declare an error.

I am also including an image that will help you determine where the noise you are hearing is coming from. The second image describes how to get to the leveler and other components under the basket.

I highly recommend having a trained service technician evaluate this problem. You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I hope this is helpful. Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post. Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
May 18, 2011
Q:

Why is my Kenmore Elite washer model 11022062101 displaying the CA code when it is ready to spin?

A:

The CA error code indicates that the average current amp draw from the motor windings exceeds 5.5 amps. This can be caused by overloading the washer. Remove some of the load and see if you still get the CA error code. Run the washer with no clothes added and see if the error code appears. If it does, then a friction problem, a motor control problem or a drive motor failure could be causing this error code. I recommend calling a service technician to diagnose and repair this type of washer problem.

Read More
Lyle W -
Sears Technician
April 06, 2009