Model #11022032100 Kenmore residential washers

  • Top And Cabinet
    3 Results
  • Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake/clutch/gearcase/motor/pump
    3 Results
  • Machine Base
    3 Results
  • Control Panel
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
  • Brake And Drive Tube 388952
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

how to install part #8577278

A:

Thank you for your question and I understand your concern.

The electronic control board is located inside the control which is pretty simple procedure to access and replace.

NOTE: Disconnect the power cord from the power source before servicing. 

To access the control board, you will need to place the control panel in the service position. You will need to remove the left and right end cap covers. See images below for instructions.

Grasp the rear upper part of the end cap cover and lift it up just enough to clear the control panel and hinge it forwards and off. Remove the screw located at the bottom of each control panel end cap. Slide the control panel towards the front of the washer and lift it up and hinge it over the rear panel. You will see the control board fastened to the bracket. 

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
August 05, 2013
A:

Phyllis: You are welcome and thank you for using Manage My Life. Have a great day!

Read More
Joey S -
Sears Technician
August 06, 2013
See more answers
Q:

kenmore elite model #11022032100 wont power up unless you unplug it for awhile.

A:

Hi Lou,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your washer.

Most likely you have a component that is overheating or an electronic failure. This may prove to be a difficult thing to trace down.

I recommend running the diagnostic routine to see if you can get an error code. I have included that information in an image below.

I highly recommend having a trained service technician evaluate this problem. You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use for parts purchases or to view your parts list diagram Sears Parts Direct .

Please perform the diagnostic tests detailed here and report back with your findings. I am looking forward to assisting you again in the near future. Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
June 27, 2011
A:

Here is that image. Landell

Read More
Landell -
Sears Technician
June 27, 2011
See more answers
Q:

I have a Kenmore elite washer, model # 11022032100. At the end of the cycle the clothes end up very soggy and wet. The spin cycle is not working properly.

A:

Thank you for your question.

I am sorry you are having a problem with the washer. If the clutch drum on top of the gear case is spinning when the washer should be spinning, we know the motor and the gear case are fine. That makes the problem either a failed clutch or basket drive. I have provided you with the instructions on how to replace the clutch and the basket drive below. Once you have the gear case removed, you can reach up and turn the plastic lever on the basket drive. When it is turned, it should release the brake and the basket should turn. If the basket does not turn, I recommend replacing the basket drive and the drive block with the clutch. I hope this is helpful.

Please let me know if you need further assistance.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 31, 2010