Model #11021102010 Kenmore residential washers

  • Top And Cabinet Parts
    3 Results
  • Controls And Water Inlet Parts
    3 Results
  • Basket And Tub Parts
    3 Results
  • Gearcase, Motor And Pump Parts
    3 Results
  • Optional Parts (not Included)
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer Kenmore model 11021102010 how to bypass the door lock

A:

There is not a way to safely bypass that door lock on your washer. Since the washer spins the basket at high speeds, that door lock is a necessary safety device. I do not recommend that you attempt to bypass it.

Read More
Lyle W -
Sears Technician
December 08, 2011
A:

Hello Frank. I do not recommend that you attempt to bypass the lid switch on that washer. I recommend that you diagnose the cause of your lid switch failure and replace or repair the defective component. The first image below shows a wiring diagram of the washer with that lid switch circuit traced in wire colors. I recommend that you UNPLUG the washer and check the wiring connections first. If those connections are okay, you can check that lid switch in the manual diagnostic test mode as shown in the 2nd and 3rd images. The 4th image shows additional testing and troubleshooting information for that lid lock assembly. That information should help you determine the cause of this failure. You can order parts from this page: Kenmore Washer 110.21102010 Parts . If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
June 11, 2012
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
June 11, 2012
A:

Hello Theresa. I am sorry to hear that you are disappointed in your website and our expert answers. We try to provide responses that are safe and effective. If you have a particular failure that you are trying to repair, reply with the details and we will try to provide safe, detailed troubleshooting advice.

Read More
Lyle W -
Sears Technician
June 10, 2013
A:

Helen: No we have not recieved any response and we likely will not hear anything. Lid locks are needed due to liability. Washers today are engineered with no type of breaking system to stop the basket from spinning and this is why lid locks are used. Todays washers do not have a breaking system to stop the washer from spinning so this is why they have lid locks. I do not see any change in future models.

Read More
Joey S -
Sears Technician
August 13, 2013
See more answers
Q:

I HAVE A KENMORE 110-21102010 WASHER WILL NOT FILL WITH WATER

A:

Thank you for submitting a question to Manage My Life.

The first thing I recommend is checking for error codes. The error codes are extremely important in the diagnosis of this type of washer. This washer has a way to recall error codes. If the control detects a problem it will identify it with an error code. I am including this information in a set of images below.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

Here is a link that you may use to view the parts list diagram or purchase any parts needed for your appliance; Sears Parts Direct .

Please perform the diagnostic tests detailed here and report back with your findings. Be sure to record any failures and when they occur along with any error codes that are displayed.

Landell

Read More
Landell -
Sears Technician
July 18, 2012
Q:

time chart for cycles on Kenmore Washer Model 11021102010 ser # c10420302

A:

Thank you for your question and I understand your concern.

The cycle times are not provided or available because the length of cycles is based on how long it takes to fill, load sizes, how long it takes to drain, off balances, vibration, one rinse or two and if it detects over sudsing. The times can very depending on the condition and the load. If you're accustomed to the standard Kenmore direct drive washer your new one will seem to run twice a long or it may take twice as long to complete a cycle but the good thing is its more energy efficient.

Read More
Joey S -
Sears Technician
March 31, 2011