Model #1070 Hoover vacuum, upright

  • Agitator
    3 Results
  • Cleaningtools
    3 Results
  • Handle
    3 Results
  • Hose
    3 Results
  • Mainbody
    3 Results
  • Motor Assembly, Hood
    3 Results
  • Outerbag
    3 Results

Question and Answers

Q:

Lawnmower Flywheel fan screw question

A:

Thank you for your question.

I am sorry you are having difficulties with the parts. I have provided you with an image below that I have labeled the parts. The fan bolts secure the fan to flywheel. The screen screws secure the screen to the top of the flywheel fan. Here is a link to order any parts you need. Sears Parts Direct .

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
June 02, 2011
Q:

vacuum wont work

A:

Thank you for your question on the vacuum cleaner not running.

I am sorry but I do not have a wiring diagram for this old vacuum cleaner from the 90's.

The little metal box is the speed control for the motor.

It works with the slide control on the handle along with the three position switch on the hose and the on off switch.

If you have power to the speed control box but not out of it then that part has failed. This speed control is no longer available as a replacement part.

You may want to wire the motor directly to the on off switch but you will no longer have different speeds for the vacuum cleaner. Please let me know what you discover. I am sorry that I could not help you more.

Sam A.

Read More
Sam A -
Sears Technician
October 03, 2012
A:

Thank you for the update on the vacuum cleaner. I did not know if when you applied 110 volts directly to the motor whether it worked or not? I sure sound like you have a bad connection somewhere and if the motor didn't work before it could be a worn brush on the motor. It certainly is old enough to have worn the brushes out. I have one about that age also and I changed the motor a couple of years ago. Please let me know if changing the brushes worked. Sam A.

Read More
Sam A -
Sears Technician
October 04, 2012
See more answers
Q:

Kenmore Elite Pro single wall oven beeps and errors out

A:

I recommend that you first try to reset the electronic control boards in the oven by shutting off the house circuit breakers for the unit to completely disconnect electrical power. Leave the power off for 5 minutes. Restore power and see if the control works properly. In some situations, that will resolve the problems that you are describing.

The ERR code is normally displayed when the function knob is changed without turning the dial to Off first as shown in the first image below. If you are seeing that ERR code randomly when the oven is heating without changing the mode, then the mode selector potentiometer switch (part 318601700) may need to be replaced. You may also have a problem with the electronic oven control board (part 316460200). There is a chance that a wire harness connection failure could be causing this problem. You can check the wiring connections using the wiring diagram in the second image below as a guide.

The resistance of that oven temperature sensor probe appears to be lower than normal. I posted a temperature/resistance chart for that temperature probe in the third image. I recommend that you shut off the house circuit breakers for the oven and check the resistance from the electronic control board in the console. I marked that connection on the wiring diagram in the second image (in violet or purple). The third image shows a drawing of the control board with that oven temperature sensor connection marked with the red arrow. You can check the resistance through the entire sensor circuit using that information.

These initial tips may help you resolve those oven problems on your own. You can order parts from this page: Kenmore Elite Pro Wall Oven Model 790.41003603 Parts . Be sure that you shut off the house circuit breakers for the oven to completely disconnect electrical power before accessing internal components and replacing parts.

You should be able to access the control board in the console by opening the oven door and removing the screws underneath the console. Lift the console and carefully fold it forward.

If you need more help, reply with additional details and we will assist you further.

Note: If you replace the electronic control board noted above, you will need to calibrate the potentiometer as shown in the 4th image.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 30, 2013
A:

Here are the first 3 images.

Read More
Lyle W -
Sears Technician
January 30, 2013
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
January 30, 2013
A:

Thanks Justin. Let us know if that fixes the problem. That information could help us and other readers.

Read More
Lyle W -
Sears Technician
February 04, 2013
A:

Hello Justin. You seem to indicate that the oven is working properly but that the temperature is not being properly displayed. You may need to use the calibration procedure shown in the 4th image above to fix the temperature display problem. If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
March 12, 2013
A:

Hello Ken. I apologize for the problems with the images. The first image about the ERR code is on page 9 of the Owner's Manual. Here is a link for the second image: Oven Wiring Diagram. Here's the link for the third image: Oven Temperature Sensor. Here's the fourth image: Oven Calibration.

Read More
Lyle W -
Sears Technician
December 29, 2014
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show