Model #10657572790 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the exact width of my Kenmore refrigerator model 10657572790?

A:

The exact width specification within 1/8" for this model is not available. The original measurement specifications included in the documents that were used to sell this model are no longer available. Even if the specifications were available, they can differ slightly from the actual product.

Based on similar models, I estimate that the measurement specifications were:

  • Height - 65 5/8"
  • Width - 35 1/2"
  • Depth - 33 3/4" with handle (31 3/4" without handle)
To determine the exact size specifications, you may need to physically measure the cabinet.

This model would not have be considered counter depth if it exceeds 29" without the handle.

You can view the specifications for current models of refrigerators on the Sears.com website www.sears.com for comparison purposes if you are trying to replace this refrigerator with one that is the same approximate size.

Read More
Lyle W -
Sears Technician
November 14, 2008
Q:

refrigerator model 10657572790 quit amking ice

A:

Make sure that the wire shut-off arm is in the down position. If this arm is even partially stuck in the "up" position then the ice maker will not cycle.

The links for previous answers provided by Maira in the above response indicate that you should check the fill tube above the ice maker to see if it is frozen. This will prevent the ice maker from getting water.

If the ice maker has ice in the mold, then it is not likely that you have a water fill problem. You can try to manually cycle the ice maker in this situation. Unplug the refrigerator and remove the cover of the ice maker as shown in the first image. The second and third images show how to initiate a harvest cycle by placing an insulated jumper wire in the T and H contacts of the ice maker module. Once you have the insulated jumper wire in place, plug the refrigerator back in and see if the ice maker starts the harvest cycle.

If the ice maker cycles and fills, I recommend that you reassemble it (without the jumper wire in place) and see if continues to cycle and work properly. If not, then the ice maker module (part 4317943) will need to be replaced. You can order that part from the Sears PartsDirect website. Here is a direct link for that part: Icemaker .

If the ice maker cycles but does not fill, then I recommend that you unplug the refrigerator and check the resistance through the water valve circuit as shown in the 4th image. You will need to use a volt/ohm meter to make that resistance check. If the resistance is okay, you can place an insulated jumper wire in the L and V contacts to see if the water valve will work (with the refrigerator still unplugged ). Be prepared to catch fill water when you plug the refrigerator back in. Plug in the refrigerator briefly and see if water is supplied to the ice maker. If the ice maker does get water, then an internal contact in the ice maker is probably bad and the ice maker module will need to be replaced. If the water valve does not work with the L and V contacts jumped then the valve will probably need to be replaced.

If the fill valve circuit does not measure the correct resistance, then you could have a bad water valve or a problem with the wiring in that circuit. You can try the test described in the second link provided by Maira to check the valve in this situation.

These tips should help you diagnose and repair your ice maker. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 01, 2011
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
January 01, 2011
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show