• Recently Viewed  
  • Cart 

    Your Shopping Cart

    Showing last added item

    Parts Qty

    Total items:

Can't locate your model number? Use our finder

Choose your product type

Common model number plates

View sample model numbers by selecting your product brand


Wards Npa Electric trimmermodel #1100

Add this model to "My Models" for easy access later.

Wards Npa Electric trimmer Model #1100 was saved to your profile.

You have reached the maximum number of models that can be added to your list.

Please Sign In or Register to have unlimited usage.

Questions & Answers about this model powered by

We have a team of experts and an active community here to answer any questions you have. In addition to help from the community, our experts actively follow up on questions to get you the information you need.

What does F2 error code mean on a Kenmore oven model 911.40161690?

I had a 24” Kenmore wall oven start giving me F2 error messages, so I put one in from my neighbor's house that he didn't need anymore. Same problem....so I am thinking it must be some type of electrical problem instead of the oven???? I don't want to call out a repairman if it isn't the oven, but can't find the right error code or manual!!! Help!

Posted April 06, 2009


Joey S, April 10, 2009

The "F2" error code indicates that the oven is getting too hot in temperature while baking or while in the cleaning mode cycle. (Oven control senses an oven temperature above 615 degrees)

Possible causes:

  • Welded relay contacts (Heating element ON while oven is in the OFF mode)
  • High resistance in the oven temperature sensor probe or high resistance in the oven temperature sensor probe circuit.
  • Electrical noise interference in the sensor circuit (Ham radio, cordless phone etc.)

The oven temperature sensor will need to be removed and disconnected and measured with an ohm meter. It should have a resistance measurement of 1100 ohms at room temperature. If the resistance is approximately 1100 ohms at the oven sensor reconnect it and then the oven sensor harness will need to be disconnected from the oven control board and re-measured. If it reads approximately 1100 ohms the likely failure is the control board or RF interference. (Ham radio, cordless phone etc.)

The oven sensor can be found secured to the rear wall inside the oven cavity. It will secured by two screws. Remove the oven sensor and disconnect the two wires and then using an ohm meter measure the resistance across the two wires. NOTE: Disconnect power to oven before servicing the oven.


Please log in or register to add your comments.

Join this conversation

Join the

Have a repair or installation question about this model?


M-F 6:30 a.m. - 10:30 p.m. CST
Sat 7:00 a.m. - 9:30 p.m. CST
Sun 7:30 a.m. - 9:30 p.m. CST

Call close >>

Thank you! Your model has been added.

Save model in your profile permanently

Don't have a profile? It's fast and easy to create one. Sign up now and you can access your models anytime, anywhere.

Sign In Register

Save to this computer*

This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.

*Saved models will only persist on this computer and browser. Model retention may be affected by your browser settings.

OK, Continue

Register Existing Customer? Sign In

By clicking Register, I agree to the terms of use and privacy policy.

Forgot password

The email address you entered is incorrect. Please try again.

Please enter your email address for this account. We will send you a confirmation email containing a link to reset your password. The password can be used across the entire suite of Sears websites.

Email Sent

An email has been sent to your account. Please follow the link in the email and you'll be prompted to create a new password. The password can be used for PartsDirect, Kmart, Sears, etc.

Password must include

  • At least 6 characters, no more than 15.
  • At least 1 letter (a - z)
  • At least 1 number (0 - 9)
  • No spaces
  • No special characters (i.e. %$#!@*)
  • Passwords are CaSe SEnSiTivE
  • Can't repeat same character more than 3 times in a row