• Recently viewed  
  • Cart 

    Your Shopping Cart

    Showing last added item

    Parts Qty

    Total items:

Can't locate your model number? Use our finder

Choose your product type

Common model number plates

View sample model numbers by selecting your product brand

Select

Kenmore Elite Rangemodel #79075503207

Add this model to "My Models" for easy access later.

Kenmore Elite Range Model #79075503207 was saved to your profile.

You have reached the maximum number of models that can be added to your list.

Please Sign In or Register to have unlimited usage.

Questions & Answers about this model powered by

We have a team of experts and an active community here to answer any questions you have. In addition to help from the community, our experts actively follow up on questions to get you the information you need.

Kenmore Dual Elite Oven not heating

Kenmore 790-75503207 oven not heating up. Element resistance is ~18 ohms. Temperature indication appears correct. Side oven works, broiler works. Can hear relays picking up for short while then dropping out, but appears to only be K2 picking up and not K1 when looking at voltage on E7 & E6. Is there something else that it could be other than the control board (318010102) ? Is there a circuit diagram available for 318010102 ?

Posted December 31, 2012

Answers

Marc, December 31, 2012

The oven not heating can be concerning. I found some information for you that I am hoping will help you with the oven. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that this will help you with the oven.

Lyle W , January 03, 2013

There is not an internal circuit diagram available for the specific control board component (part 318010102). I posted the wiring schematic for the range in the image below. That range uses a DLB (Double Line Break) relay in that L2 leg of power as shown in that image. I traced the circuits for the bake element on that wiring schematic. If the element is getting the L1 leg of voltage but not the L2 leg, then that DLB relay could be causing your problem. You could also have a wiring failure or a bad electronic oven control board (part 318010102). This information should help you test those components to determine the cause of your failure. Note: Use extreme caution when checking live voltage. Wear electrical safety gloves and safety goggles. Unplug the range after live testing is completed. The range should be unplugged when internal components are accessed or exposed . If you need more help, reply with additional details.

You can order parts from this page: Kenmore Elite Range Model 790.75503207 Parts . As noted above, be sure that you unplug the range before accessing internal components and replacing parts.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Don, January 03, 2013

Thanks for the info but the oven is already fixed. I traced the fault to the BA relay on the control board. I removed the BA & BR relays and installed the healthy BR relay in place of the failed BA relay, now the oven works fine and broiler is awaiting a new relay. I will buy a new relay for $3 and install in BR instead of paying $250 for a new control board when only a $3 relay failed. From reading this forum along with several others, this appears to be a common problem with this control board and BA relay after about 4 or 5 years. I will buy a few extra so when it happens again, I'll be ready. The Omron G8P-UA-006203 relay is a proprietary build, but per other forums is identical to a standard Omron relay with a 15V coil, G8P-1A4P DC15. Hope this helps some other readers who have the same failure.

jason, May 20, 2013

I too am experiencing this SAME problem with my Kenmore 790-75503207. DON - thank you for posting your fix. I'm going to give it a try, just need a little guidance. any chance you can post a little more detail how to fix? I'm talented in many area's, so fixing this shouldn't be too much trouble, I'm just not sure where to start... take the current control board off/out of the Stove? then..... Thank you, Jason

1

Please log in or register to add your comments.

Join this conversation

Join the
Conversation

Have a repair or installation question about this model?

Hide

M-F 6:30 a.m. - 10:30 p.m. CST
Sat 7:00 a.m. - 9:30 p.m. CST
Sun 7:30 a.m. - 9:30 p.m. CST


Call close >>

Thank you! Your model has been added.

Save model in your profile permanently

Don't have a profile? It's fast and easy to create one. Sign up now and you can access your models anytime, anywhere.

Sign In Register

Save to this computer*

This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.

*Saved models will only persist on this computer and browser. Model retention may be affected by your browser settings.

OK, Continue

Register Existing Customer? Sign In

By clicking Register, I agree to the terms of use and privacy policy.

Forgot password

The email address you entered is incorrect. Please try again.

Please enter your email address for this account. We will send you a confirmation email containing a link to reset your password. The password can be used across the entire suite of Sears websites.

Email Sent

An email has been sent to your account. Please follow the link in the email and you'll be prompted to create a new password. The password can be used for PartsDirect, Kmart, Sears, etc.

Password must include

  • At least 6 characters, no more than 15.
  • At least 1 letter (a - z)
  • At least 1 number (0 - 9)
  • No spaces
  • No special characters (i.e. %$#!@*)
  • Passwords are CaSe SEnSiTivE
  • Can't repeat same character more than 3 times in a row