• Recently viewed  
  • Cart 

    Your Shopping Cart

    Showing last added item

    Parts Qty

    Total items:

Can't locate your model number? Use our finder

Choose your product type

Common model number plates

View sample model numbers by selecting your product brand

Select
Get FREE Standard Shipping on orders of $90.00 or more. Details

Kenmore Residential dryermodel #11064852400

Add this model to "My Models" for easy access later.

Kenmore Residential dryer Model #11064852400 was saved to your profile.

You have reached the maximum number of models that can be added to your list.

Please Sign In or Register to have unlimited usage.

Questions & Answers about this model powered by

We have a team of experts and an active community here to answer any questions you have. In addition to help from the community, our experts actively follow up on questions to get you the information you need.

kenmore 80 series dryer no heat

i have a kenmore ele dryer 80 series tumbler works fine all settings. the only thing not working is the heating element on all high med and low

Posted September 12, 2012

Answers

Joseph P., September 12, 2012

I am sorry that you are having some difficulties with your dryer and I will be happy to help. I suggest you add to the thread of this question and include the full model number of your dryer so that the expert can provide you with a more detailed answer. I did manage to find a link that will provide you with some good information. I hope this helps with your dryer troubles while you wait for your expert response.

max, September 12, 2012

i purchused it in 01 28 05 mod 110.64852400 ser ms0102177 typ dwsr-ele-2406028-cv54

Joey S, September 13, 2012

Thank you for your question and I understand your concern.

Since the heating requires 220 volts, the two house circuit breakers dedicated for the dryer should first be reset. Reset both circuit breakers by flipping them OFF and ON 2-3 times and then check to see if the dryer will heat. If it does not heat, the voltage supply should be measured and confirmed with a voltage meter. The voltage should be checked at the back of the dryer where the power cord is attached. NOTE: I do not recommend measuring voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dryer. There will be three terminals on the terminal block. The voltage should be measure across the two outside terminals. If the voltage is correct (220), the thermal fuse will need to be disconnected and tested for continuity with an Ohm meter. The thermal fuse is located behind the dryer and it will be mounted on the blower wheel duct. The thermal fuse will have RED wire and Red wire with a White stripe connected to it. NOTE: Disconnect the power cord from the power source before removing the rear panel. Disconnect the wires from the thermal fuse and check it for continuity. If it does not measure continuity, replace the thermal fuse and your dryer will likely heat again. In the image added below; the thermal fuse is key #33.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

1

Please log in or register to add your comments.

Join this conversation

Join the
Conversation

Have a repair or installation question about this model?

Hide

M-F 6:30 a.m. - 10:30 p.m. CST
Sat 7:00 a.m. - 9:30 p.m. CST
Sun 7:30 a.m. - 9:30 p.m. CST


Call close >>

Thank you! Your model has been added.

Save model in your profile permanently

Don't have a profile? It's fast and easy to create one. Sign up now and you can access your models anytime, anywhere.

Sign In Register

Save to this computer*

This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future.

*Saved models will only persist on this computer and browser. Model retention may be affected by your browser settings.

OK, Continue

Register Existing Customer? Sign In

By clicking Register, I agree to the terms of use and privacy policy.

Forgot password

The email address you entered is incorrect. Please try again.

Please enter your email address for this account. We will send you a confirmation email containing a link to reset your password. The password can be used across the entire suite of Sears websites.

Email Sent

An email has been sent to your account. Please follow the link in the email and you'll be prompted to create a new password. The password can be used for PartsDirect, Kmart, Sears, etc.

Password must include

  • At least 6 characters, no more than 15.
  • At least 1 letter (a - z)
  • At least 1 number (0 - 9)
  • No spaces
  • No special characters (i.e. %$#!@*)
  • Passwords are CaSe SEnSiTivE
  • Can't repeat same character more than 3 times in a row