Model #YKGRC608LS0 KITCHENAID Free Standing, Gas

  • Cooktop Parts
    3 Results
  • Cooktop Burner Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Drawer Parts
    3 Results
  • Oven Chassis Parts
    3 Results
  • Broiler & Oven Burner Parts
    3 Results
  • Oven Parts
    3 Results
  • Rear Chassis Parts, Miscellaneous Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

KitchenAid Superba gas range Model # YKGRC608LS0 display problem

A:

The problem with the control panel on the range is concerning. I did some research on your model number but was not able to find a solution. Your expert will be able to help answer your question. It may take two business days for your expert to reply. If you would like to look into Sears doing the repair here is a link for Sears Home Services. I do hope that everything works out.

Read More
Marc -
July 26, 2013
A:

Thank you for contacting ManageMyLife.com regarding the display on your KitchenAid gas range randomly going on and off. I'm happy to help you today.

Based off of your description, it is possible there is a loose wiring connection causing this problem. The images below will assist you with accessing the control panel components. Please be sure disconnect power to the range before accessing internal components. After checking to make sure the connections are secure, reassemble the unit, plug it back in and check for operation. This may correct the issue. If not, it is possible the microcomputer/display board (p/n 9782455) may need to be replaced. If you take the control board out, you can go over it with a magnifying glass to check for bad solder joints. This would indicate that the board is indeed the culprit.

Parts can be purchased from Sears PartsDirect. If you do not feel comfortable repairing this issue yourself, service can be scheduled at the following link: Sears Home Services.  

I really hope this information helps you today. Thank you for contacting ManageMyLife.com.

Read More
Korinna S -
Sears Technician
July 27, 2013
A:

Here is an addition image.

Read More
Korinna S -
Sears Technician
July 27, 2013
See more answers
Q:

my kitchenaid range had all power leave except a small c on the front electrical panel. When I reset the electricity a code Err F2E1 for stucK/shorted key fix?

A:

Appliance error can be confusing and upsetting. There is not always a game plan available for when things go wrong. I did locate a previous expert post for this error. I attached to the link below if you would like to check while waiting for the expert. I see you have made some repairs but if you would like a technician to visit and make repairs you can use the Sears Home Services scheduler below.

Read More
Barbara H. -
September 09, 2011
A:

Thank you for your question and I understand your concern.

The "F2/E1" fault code is indicating a stuck or shorted key pad. Based on your details; part #W10181439 is the electronic oven control and not the key pad/membrane switch. Without having the complete model number I will not be able to confirm the part number of the membrane switch. You will need to replace the membrane switch based on the "F2/E1" fault code.

You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
September 12, 2011
A:

I have a Kitchen Aid - Superba Gas Range Model# YKGRC-608LS0. After the power is off and comes back on, the clock and the panel works fine. However, the moment I turn on the gas on the range and the burner comes on, within a few minutes, it shows an F2:E1 error. Is this the same keytail connector ribbon cleaning issue?

Read More
Anonymous -
September 28, 2011
A:

For the anonymous writer in the above response: That F2:E1 on your gas range is different than the one shown for that model KESS907SBL discussed above. That code on your model YKGRC-608LS0 indicates that you have a problem with the Cancel key on that keypad. I provided a list of the fault codes for your range and a wiring diagram in the first image below. The next 3 images show how to access the control components. There is a chance that a loose wiring connection could be causing your problem. I recommend that you clean that touch panel first. If cleaning that panel does not help, you can SHUT OFF THE HOUSE CIRCUIT BREAKER FOR THE RANGE and access the control boards in the console. Check the ribbon wire connections. If the connections are okay, you will probably need to replace the key panel (part 9782418CB). There is a chance that you may also need to replace the user interface display control board and/or the power control board. These control components are expensive. Instead of attempting to replace parts yourself, you may consider having a service technician diagnose the range and replace parts so that you are not at risk of buying unecessary components. I provided a link for the Sears Service website below this response. I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
September 29, 2011
A:

Here is the final image for the above response.

Read More
Lyle W -
Sears Technician
September 29, 2011
See more answers

Top Parts