Model #X3 SUPERWINCH Winch

  • Unit
    3 Results
Find part by diagram >

Question and Answers

Q:

Excessive condensation leaking out of fridge

A:

I can see how this will be frustrating to have water leaking in your refrigerator especially with little ones .We depend on our fridge very much .I have provided a link through the Mange My Life website that may be helpful until a Expert responds. Have a great day!

Read More
Carmen G -
July 29, 2012
A:

I know that it can be very difficult to have issues with your refrigerator. Something like this is caused by a blocked defrost drain outlet. If the water from the defrost cycle does not flow down the defrost drain hose & out to the drip pan below the refrigerator you will get water under the crispers & other places. You will need to pull the freezer rear panel off & inspect the defrost drain. You can clean & flush out the drain with hot water. Be sure to dump the defrost drain pan water after clearing the clog. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
AnneJ -
Sears Technician
July 30, 2012
A:

had this problem too x3 now as i read this site seems to be a common issue and i hope sears (though this is made by samsung) will stand behind product and make this right!!

Read More
erin -
January 06, 2016
See more answers
Q:

Were can I get a new motor? 315CR2000 Craftsman Trimmer

A:

Thank you for your inquiry on your Craftsman Trimmer, Model: 315CR2000. From reviewing the details on your model, it appears that the motor for your trimmer is not available.  

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

 

Read More
Gerry 93 -
Sears Technician
May 29, 2015
Q:

Another Follow up Question on 596.76253702 Defrost Problem

A:

Here is how to continue your conversation with your expert without asking a new question each time. Go to www.managemylife.com On the homepage in the top right hand corner click on log in After logging in, you will be redirected back to the homepage From the home page back in the top right hand corner click on your name/profile This will direct you to your profile page Scroll down to the bottom of your profile page, until you see "(your name) conversations" Click on the question you'd like to view Towards the bottom of your conversations, you'll see "Join this conversation" From here, you can reply back to the Expert by adding more details Once you've added your response click "reply" Please remember, your experts generally reply within two business days with answers and advice, sometimes sooner. You will receive an email once you're question has been answered. I hope this helps.

Read More
James -
March 07, 2012
A:

While it has a sufficient frost build up, the back panel in the freezer will need to be removed. This will require taking everything out of the freezer. Be sure to disconnect the power first. With the back panel out, you will see the evaporator and at the top will be the defrost thermostat and some wires. First disconnect the brown and orange wires from the thermostat (see wire diagram). Now, check the ohms resistance across these wires. The meter should read all zeros. If it reads nothing at all, the thermostat will need to be replaced. If it's ok, next disconnect the white wire from the heating element. If you get any reading at all, the element will be ok. If there is no reading or all zeros, the element will need to be replaced. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
March 08, 2012
A:

Scott, Thanks much. I read this on the other thread and am ready to attack when I get back in a few days. I'll let you know how it goes. Just to be certain, is the check on the heating element's white wire also a resistance reading? If so, is there another wire to connect to so as to complete the circuit?

Read More
David -
March 08, 2012
A:

David, yes it will be a resistance check. Use the same orange wire that was used on the thermostat and the wire on the other side of the heating element that is connected to the white wire. I hope this will help you.

Read More
Scott D -
Sears Technician
March 08, 2012
A:

Scott, I finally had a chance to get in there and need some more help in getting the back cover off (the evaporator cover, according to the diagram.) I removed the 3 hex head screws in the corners. I couldn't get the fan shroud cover unsnapped, though. We don't have the ice maker connected; should it just be removed as well? Any help with this sequence would be appreciated.

Read More
David -
March 16, 2012
A:

David, the fan shroud should not need to be removed. It should come out with the cover. The icemaker will need to be removed to get the cover out. I'm attaching a picture of how to remove the icemaker. I hope this will help you.

Read More
Scott D -
Sears Technician
March 19, 2012
A:

Scott, Thank you for your continued help. I finally got back to it tonight. Taking off the icemaker was simple enough. (Since we're not using it, may I assume that it can stay out?) However, I still can't remove the back panel. There was one more screw next to the water input to remove. After doing that, I still cannot pry the panel off from the top. At the bottom, it is obstructed by the slide mechanism for the bottom drawer, and I can't figure out how to remove that, if it indeed needs to come out. I'd appreciate any help for the next step....

Read More
David -
April 02, 2012
A:

David, I'm sorry you are having this problem. The rails will need to be removed. They have screws holding them in place. I'm attaching more information to remove the back panel and rails. I hope this will help you. If you would like to have a technician check this, you can call 1-800-469-4663 to schedule a tech to come out. If you would like more assistance, please let me know and I will assist you further.

Read More
Scott D -
Sears Technician
April 02, 2012
A:

Thanks, Scott. The only screws I see for rail removal are the two white ones (to match the liner - which is what I had thought they were holding on) on either side of the compartment, directly in front. Is it just those?

Read More
David -
April 02, 2012
A:

It should just be 2 screws holding the rail. One in front and one in back. If you can send a picture of the rails, it would be very helpful.

Read More
Scott D -
Sears Technician
April 02, 2012
See more answers