Model #WTW6700TW1 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Motor, Basket And Tub Parts
    3 Results
  • Pump Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

F 50 error WTW6700TW1 Whirlpool Residential washer

A:

Thank you for your inquiry on your Whirlpool Residential Washer, Model: WTW6700TW1. From reviewing the detail on your model, I have included a picture which gives the error code information below. 

Safety warning: before beginning this repair, disconnect the power supply to the washer to prevent risk of injury from electrical shock. 

If you don’t feel confident/comfortable repairing this problem yourself, then you could have it repaired at your home by one of our technicians. The link to the website and the phone number are below. Sears Home Service or 1-800-4MY-HOME(1-800-469-4663)

I hope this answered your question. Thank your for contacting SearsPartsDirect.com and have a wonderful day. 

Read More
Gerry93 -
Sears Technician
February 12, 2015
Q:

troubleshooting WTW6700TW1 Whirlpool Residential washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is displaying an error code. 

The F then 54 flashes when the machine/motor
control detects high current for the motor module.
? Does basket turn freely? If not, determine
cause of friction.
? If basket turns freely, see TEST #3, page 4

TEST #3 Motor Circuit
This test checks the wiring to the motor and rotor
position sensor; and the motor and rotor position sensor
themselves.
NOTE: Drain water from tub.
1. See Activation of Manual Diagnostic Test Mode,
page 2 and check the motor and electrical
connections by performing the Spin test under
Manual: Motor, page 2. The following steps assumes
that this step failed.
2. Unplug washer or disconnect power.
3. Check to see if basket will turn freely.
? If basket turns freely, go to step 4.
? If basket does not turn freely, determine what is
causing the mechanical friction or lock up.
4. Remove the console to access the machine/motor
control assembly. See Accessing & Removing the
Electronic Assemblies, page 6.
5. Visually check that the P5 and P10 connectors are
inserted all the way into the machine/motor control.
? If visual checks pass, go to step 6.
? If visual checks fail, reconnect P5 and P10 and
repeat step 1.
6. Visually check that the P5 and P10 connectors are
inserted all the way into the machine/motor control.
? With an ohmmeter, verify resistance values as
shown below:

P5- 1-2 and 1-3 31Ω±5Ω - go to step 7 if values are much higher than 31Ω.
P10- 6-5, 6-4, 6-3 1.5 KΩ ±100Ω- go to step 7 if values are much higher or much lower than 1.5kΩ.
1-7 600Ω to 21.2 K Ω go to step 7 if out of range.

7. Tilt machine forward to access the bottom of the
machine and the drive motor area. See figure 1,
page 14. Remove the motor bolt, then the motor
cover to access the motor connections. 
8. Visually check the mounting bracket and electrical
connections to the motor and rotor position sensor
board.
? If visual check passes, go to step 9, page 5.
? If visual check fails, reconnect the electrical
connections, reassemble stator and motor cover
and repeat step 1.
9. With an ohmmeter, check for continuity between all
pins on the P10 machine motor control connector
and the motor rotor position sensor (RPS) connector.
See figures 2 and 4, pages 14 and 15.
? If there is continuity, check the motor windings. If
the motor windings are open, replace the drive
motor.
? If there is no continuity, replace the lower machine
harness.
10. With an ohmmeter, check for continuity between all
pins on the P5 machine/motor control connector
and the drive motor connector.
? If there is continuity, replace the drive motor.
? If there is no continuity, replace the lower
machine harness.
11. The drive motor and lower harness are good.
Replace the motor RPS board and perform the
Diagnostics test in step 1 to verify repair.
12. If the Diagnostics motor test in step 1 failed, then
the machine/motor control has failed:
? Unplug the washer or disconnect power.
? Replace the machine/motor control assembly.
? Perform the Motor Diagnostics in step 1 to verify
repair.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
October 14, 2014
Q:

Long Fill error code WTW6700TW1 Whirlpool Residential washer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when having the trouble with the long fill in the washer.
 
Glad to help out.   Im  looking at your Kenmore Washer model number WTW6700TW1.

Sorry this is driving you crazy.   I understand very well because of the importance of this appliance.   I am going to give  you all the information on the LF in my technical manual book.  

LONG FILL--LF flashes when the water level does not change for a period of time OR water is present but control does not detect the water level changing.

1. -> Is water supply connected and turned on?

2.->  Are hose screens plugged?

3.->  Is water siphoning out of the drain hose?  Check for proper drain hose installation.

4.-> Is the pressure hose connection from the tub to machine?motor control pinched, kinked, plugged or leaking air?

Lots of times with others they have taken the pressure line and blew it out.   If stuck then you need a new pressure line.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".

Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 
 

Read More
Larry L -
Sears Technician
April 03, 2014
A:

Larry, THANK YOU! THANK YOU! THANK YOU! THANK YOU! THANK YOU! ...so I preemptively bought the cable harness...I couldn't wait any longer so I removed the back panel and control cover, removed the old hose, submerged in water, covered one end and blew in the other....WOOHOO...a leak. I was so happy. I went to hardware store and bought tubing with same ID. Replaced, reassembled, and my poor wife has about three weeks of laundry to do. That was the best $3 I have ever spent. THANK YOU! THANK YOU! THANK YOU! THANK YOU! THANK YOU! You rock!

Read More
Juan -
April 06, 2014
See more answers

Top Parts