Model #WTW58ESVW1 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Controls And Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Whirlpool starting in the middle of cycle

A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. It sounds like you're experiencing an issue with the timer. The provided model number of W10140920 is not coming up as a valid model number. Please rechek this number and reply back to this thread for further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
October 18, 2013
A:

Whirlpool WTW58ESVW1

Read More
Ronnie -
October 18, 2013
See more answers
Q:

Whirlpool washer help.

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
January 15, 2012
A:

To add to the above question, it agates not spins while it fills with water. At the end of the spin cycle it starts to add water again. Clothes end up wet at the end of the cycle. Model # wtw58esvw1

Read More
Mike -
January 15, 2012
A:

Hi Mike,

Thank you for submitting a question to Manage My Life.

This is most likely being caused by a bad load sense switch but it can also be a bad timer. The diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

If you have an ohm/volt meter and are confident in your technical abilities, please reply below and I will be happy to assist you further.

Landell

Read More
Landell -
Sears Technician
January 17, 2012
A:

Thank you for your help and yes I would like to perform this task myself. Can you give me the step by step process to complete these task? Thanks!

Read More
Mike -
January 17, 2012
A:

Hi Mike, I am including the checks you will need to make with your meter in the images below. Start a fill and when your washer is filling and spinning check blue/orange to white. I have marked the white and blue/orange with arrows. If you have voltage blue/orange to white the load sense switch (part number W10177795) is faulty and will need to be replaced. I hope this is helpful. Check the things I have covered here, and if I may be of further assistance please reply to this post. Landell

Read More
Landell -
Sears Technician
January 18, 2012
A:

Thank you!

Read More
Mike -
February 06, 2012
A:

Hi Mike, You're welcome. Glad I could help. Please keep Manage My Life in mind for all of your do-it-yourself projects. Landell

Read More
Landell -
Sears Technician
February 07, 2012
See more answers
Q:

Washer not filling

A:

A Washer is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Priscilla V -
November 08, 2011
A:

From the description you give I suspect the problem is then W10248227 ATC/Load Sensing switch.

The switch is located in the console area. The image below shows how to raise the console. Remember to unplug the washer first. The wiring in the 2nd image may be of help to you.

The switch can be obtained at the following link: Sensing Switch .

You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
November 09, 2011
A:

Thank you for your input. How can I test this switch? It is an 85$ part and would like to be sure that is the problem, before ordering it. The part number you gave me is for a wiring diagram, I am assuming the part you are speaking of is #W10248240, is this correct?

Read More
dave -
November 09, 2011
A:

The Load Sensing switch is W10248240. If you wish to check the switch then you must be able to check live voltage to the switch. You should be extremly comfortable checking voltage with a meter. Start by verifying 120 volts to L1 and neutral. Next check voltage to the water valves. The wiring in the previous image may help you with this. Please be careful checking voltage and only if you are comfortable doing so.

Read More
Fred M -
Sears Technician
November 11, 2011
A:

FRED M Thanks for the wiring diagram showing the Load Sense Switch Where is that diagram from ? I can't find that wiring diagram at ServiceMatters thanks again

Read More
Joseph -
January 25, 2012
A:

The W10248227 wiring diagram is in our system. It is a new system and not widely available yet.

Read More
Fred M -
Sears Technician
January 26, 2012
See more answers

Top Parts