Model #WPSE4200A0WW GE Residential Washers

  • Controls & Backsplash
    3 Results
  • Cabinet, Cover & Front Panel
    3 Results
  • Tub, Basket & Agitator
    3 Results
  • Suspension, Pump & Drive Components
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Stops at rinse cycle WPSE4200A0WW Ge Washer

Q:

final spin cycle, washer starts clicking

A:

No worries! Manage My Life is here to help! An expert will be able to provide you with a detailed answer to your question. It usually takes 24-48 hours to receive a response. Have a great day!

Read More
Jackie S -
September 15, 2011
A:

Please have someone answer my question , we can not go much longer without our washer.

Read More
Patricia -
September 17, 2011
A:

Hi Patricia,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

The old control board has a model selector plug that must be removed and installed onto the new control. The model selector plug is in the upper right hand corner of the control board. I have marked this with a red arrow in the image below. This image also has the field service mode.

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
September 18, 2011
A:

the plug is soldered to the board and the new board has the same plug soldered to it, so we have no idea how we would remove it and keep it intact.

Read More
Patricia -
September 19, 2011
A:

Patricia, The model selector plug should not be soldered to the board. Look for any differences in the 2 control boards. Try running the diagnostic that I included in the image I sent you on the previous post. Also, I need to know where the clicking is coming from. Is the clicking from the control area or down at the bottom? Check the things I have covered here, and if I may be of further assistance as more details become available, please reply to this post. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
September 19, 2011
A:

the clicking is coming from the motor, at least that's where it sounds like it is coming from

Read More
Patricia -
September 19, 2011
A:

the boards are both the same

Read More
Patricia -
September 19, 2011
A:

Patricia, I found a better tech sheet on this model. This is one of the few washers of this style that has a model selector plug on the lower left hand side of the board (see image below). I apologize for the confusion. You did not mention whether or not you ran the diagnostics. This tech sheet makes this process easier to follow. Try running the diagnostics using the information below, and report back with your findings. The remaining checks will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you in any way I can. Landell

Read More
Landell -
Sears Technician
September 20, 2011
See more answers
Q:

why my GE washer wpse4200a0ww cold water wont shut off

A:

Running water can definitely run up your water bill. So I understand your concern. Below I have attached some links that will help you diagnose your issue. I hope these links are useful!

Read More
Jackie S -
May 29, 2011
A:

I suspect the problem is with the cold water valve.

The wiring diagram below will help you with this problem.

Both the hot and cold valve have neutral controlled by the water level switch. If the water level switch works for the hot then it must work for the cold also.

Even if the relay on the control stuck in the closed position the water level switch should break the circuit and stop the filling.

Most likely you will need to replace WH13X10006 water valve to correct this problem. Remember to unplug the washer first before accessing the valve.

The 2nd image below will help with this.

You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
May 30, 2011
See more answers

Top Parts