Model #WM2301HR LG Residential Washers

  • Cabinet And Control Parts
    3 Results
  • Drum And Tub Parts
    3 Results
  • Dispenser Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:



Question and Answers


Washer leaking WM2301HR


Thank You for contacting

I understand your frustration when you keep having to clean up water after each cycle. My best recomendation would be to fill the tub half way with water. Then set is to the drain cycle and watch the pump area. You may have a leaking come from the other end of the hoses that just drips down the length of the hose to spot under the pump. Plus if the filter cap is over tightened you could have cracked the casing and that could be where the leak is coming from.

If you have further questions please let me know.
Thanks for using

Read More
Desirea -
Sears Technician
October 18, 2013

I own a lg front load washer, the model nbr is wm2301hr, I have a leak in the front, I can not tell if it's the water pump or the tub seal. When I watched the the wash load from the back of the machine it is in the middle up front drip, I was not able to get to the front and see what was wet without it drying before taking off all the panels and door. What is your suggestion ? Thank you

Read More
Mercedes -
November 17, 2015
See more answers

Machine does not spin properly WM2301HR Lg Washer


washer and spin cycle smell something smoking. WM2301HR Lg Washer


Thank you for choosing and being a valued member.  I can certainly understand how frustrating it can be when your washer is not working properly.

 It sounds to me like it could be  a bad drum bearing causing your tub not to turn. 

Voltage Testing Hall Sensor at Stator:

If measuring voltage from the Main PCB Assembly to the Hall Sensor, use the
following steps:
1. Unplug power cord.
2. Remove rear washer panel.
3. Locate Hall sensor connector on the stator behind the rotor.
4. Place meter leads on terminals 5 to 4, white to gray.
5. Plug in power cord, close door, and press power button.
6. You should measure 10 to 15 Vdc. If 10 to 15 Vdc is present, control board, white wire, and gray wire are OK! If not follow testing output voltages on control
board in next section
7. To measure output signal voltage from the hall sensor, carefully move test leads to terminals 1 to 4, blue and gray. Slowly rotate motor rotor by hand. 
You should read a pulsing 10 Vdc. If 10 Vdc is measured from 1 to 4, move lead on blue wire to red wire, terminal 2. Repeat rotating motor rotor by hand.
You should read a pulsing 10 Vdc from red to gray.
8. If pulsing 10 Vdc is measured from 1 to 4 and 2 to 4, hall sensor is OK! If either test netted only 9 to 10 Vdc without changing (no pulsing) the hall sensor is
likely defective. Disconnect power by unplugging washer and ohm check hall sensor to verify failure of the hall sensor.

Cabinet cover:
1 Unscrew the 5 screws from upper of the canbinet
2 Unscrew the screw from filter cover.
3 Put a flat ( -) screwdriver or putty knife into the hinge
slots at the bottom of the cover and pry it out.
4 Unscrew the screw from the lower side of the cabinet
5 Open the door.
6 Disassemble the clamp assembly
7 Tilt the cabinet cover.
8 Disconnect the door switch connector.
9 Lift and separate the cabinet cover.
10 Disassemble the clamp assembly.
11 Disassemble the gasket.
NOTE: When assembling the CABINET
COVER, connect the door switch connector.
10 Disassemble the clamp assembly.
11 Disassemble the gasket.

4280FR4048L  and 4280FR4048E  is the rear bearing for the tub. 

You can also visit for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 20, 2015

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show