Model #WM2075CW LG Residential Washers

  • Cabinet & Control Panel
    3 Results
  • Drum & Tub
    3 Results
  • Dispenser Assembly
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

LG Washer Machine "OE" Error. Attempt to fix with comments...Help

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
December 22, 2011
A:

Hi Jason,

Thank you for submitting a question to Manage My Life.

Since you have already checked the drain pump filter, I recommend taking the tub to pump hose off and ensuring that it is not restricted with debris. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. Then check the pump to stand pipe (house drain) drain line. Make sure the drain hose has an air gap at the stand pipe. Water may be siphoning back into the washer, or if the pump has to force the water into the house plumbing this may cause an OE. The drain pump can be working as designed but if the water is not being pumped out fast enough due to a restricted drain hose the washer will give this error. Confirm that the washer is leveled properly. If the unit is not leveled properly, it will not drain properly. The front of the unit cannot be higher than the back or vice versa. If not properly leveled, the water can flow back into the machine. I am including the QC test in the images below. The QC test will check the water level frequency (pressure switch). If the QC test results are within normal limits you will need to make sure the control board is sending 120VAC to the drain pump. I have seen low voltage cause this issue. If the voltage is correct you will need to ohm the drain pump. The drain pump should ohm between 10 and 20 ohms. The next step may be to replace the drain pump.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details, in a reply to this post.

Landell

Read More
Landell -
Sears Technician
December 23, 2011
A:

I have a top loading Sears Kenmore Washer Elite. My Model Number is 796.29272000 (It can be found on the left side of your Top Panel) If you need the water pump, as I did when looking into this "OE" error I looked around since SEARSDIRECTPARTS.com was quite expensive once shipping came into play. They wanted to charge me $75 for the part and $50 for expedited service which took 5 days. Yes its cheaper than the $139 service install and the $98 for the pump from service. Lookied around and I bought it here and saved BIG! http://www.appliancepartspros.com/Appliance-Parts/lg-pump-assembly-drain-item-number-ap5206579.aspx I also saw that this pump works for the following models as well: Kenmore 79629002000 Washing Machine Kenmore 79629002010 Washer Kenmore 79629272000 Washer Kenmore 79629272010 Washer Kenmore 79629272900 Washer Kenmore 79629278000 Washing Machine Kenmore 79629278010 Washer Kenmore 79629278900 Washer Kenmore 79629472000 Washer Kenmore 79629478000 Washer Read more: http://www.appliancepartspros.com/Appliance-Parts/lg-pump-assembly-drain-item-number-ap5206579.aspx#ixzz1xA4ZGPOi http://www.appliancepartspros.com

Read More
Frank -
June 07, 2012
A:

Heres the link:

Read More
Frank -
June 07, 2012
A:

I have the same problem with my model (mine is 79641473210) and error 0E displaying. I cleaned the filter but code still appeared. Then I noticed that the drain hose was inserted too far into the drain standpipe (about 24 inches) so I pulled it and noticed some gunk up in the hose. It wasn't clogged all the way and I was able to blow into it and hear bubbling in the tub. I used a coat hanger to attempt to clean out the hose and got some stuff out. I then reran the machine in cleaning mode but got the same 0E error. The washer is about 3 years old.

Read More
Lee -
August 26, 2015
See more answers
Q:

Soap dispenser drawer is stuck

A:

I know that it can be very frustrating to have issues with your washer. This is a very unusual problem to have with this unit. I tried to duplicate this failure by rearranging the dispenser compartment covers so that they would prevent the drawer from opening. I could not find an arrangement that would prevent that dispenser drawer from opening due to an internal component problem in the drawer. There is a possibility that the drawer was inserted wrong and forced into the dispenser housing. It is likely that you will need to force the dispenser drawer back out and then remove it to check the housing and the dispenser drawer. The housing is enclosed so the only way to get the drawer out will be to use more force to pull it out. The drawer or the housing may break when you do this. If the parts are damaged, you can order new parts from the Sears PartsDirect website. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
September 25, 2013
Q:

"de" error code on lg front load washer

A:

I know that it can be very frustrating to have your washer stop working correctly. The link below will provide some information on this issue. However, the information is very technicial, so if you don't feel comfortable doing this, I would recommend that you schedule service. I hope this helps. Thank you for using Manage My Life.

Read More
aashe -
September 09, 2012
A:

Thank you for submitting your question. Anne has provided you with great information for this error code. I recommend following the provided information. Also, the door switch should be disconnected and tested for proper operation with an ohm meter. I hope this helps. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with our Sears Home Services team. Please reply back to this thread if you require further assistance with this repair. Thank you for using Mange My Life.

Read More
Tykara -
Sears Technician
September 10, 2012
See more answers

Top Parts