Model #WFW9050XW00 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

whirlpool washer WFW9050XW00

A:

I understand how frustrating it is not having your washer working right. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Yadira -
August 08, 2012
A:

Thank you for submitting your question. The washer should be providing an error message if something is work. I recommend running the unit through a diagnostic cycle to see what's going on. Your diagnostic information for your washer is provided in the image below. Please reply back to this thread with your results for further assistance. I hope this helps. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
August 09, 2012
A:

I don't see an image to check on

Read More
Kimberly -
August 09, 2012
A:

The washer modle is WFW9050XW00. It allows me to select a cycle, however when I push the start button all it does is beep at me. I can't for the life of me figure out what the issue is. I had to replace the bellow and everything got plugged back in properly and no wires are cut/crimped. It just won't start. I am in tears over this darned thing as it's not even two years old.

Read More
Kimberly -
August 09, 2012
A:

I apologize Kimberly, the diagnostic information is below. If you've recently changed the below, it may be the door lock assembly you're having an issue with. I would re-check the installation. If you didn't have to disconnect the lock assembly to replace the below, then run the unit through a diagnostic mode so we can see what's going on.

Read More
Tykara -
Sears Technician
August 11, 2012
A:

I did have to take the face of the machine off to replace the bellow. There are two different plugs, one at the top and one at the bottom. There is also two blue wires that are coated completely. I am wondering if those two wires are the problem? There is no plug that they are attached to however there seems to be a slot that the go into with a white cover over the top of them. I am willing to bet that is the problem (the two blue wires). I am going to take a look at the diagram again and see if it shows me anything. If you could tell me about those two blue wires I would be forever great full.

Read More
Kimberly -
August 11, 2012
A:

Ok I have changed the door lock, the lower wiring harness (twice), and the bellow. It worked for a week and now when I set it to run it stays on door lock/add garment. Then after a period of time it just starts beeping then I am can turn the power off to it. The door lock seems to be working (I think) it makes the locking noise but it just will not cycle.

Read More
Kimberly -
September 16, 2012
A:

have changed both boards twice. suspect wiring, connections or door locking system. have same problems as previous consumers. continues to stop or not start or restart under different situations.

Read More
JACK -
November 23, 2012
A:

model wfw 9050 x woo sr#hc025 84052.. What is wrong with whirlpool with so MANY people having this same problem.

Read More
JACK -
November 23, 2012
A:
Kurtis Barr -
January 16, 2015
See more answers
Q:

My washers stops part way through the wash cycle WFW9050XW00 Whirlpool Automatic washer

A:

Thank you for your inquiry on your Whirlpool Washer, Model: WFW9050XW00. From reviewing the details on your model, I have provided a link to a couple of videos on similar model of washers, which should be able to troubleshoot what could be causing the washer to stop mid cycle.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the washer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663.

I hope this answered your question. Thank you for contacting SearsPartsDirect.com, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 17, 2015
Q:

Washing cycle stops mid cycle WFW9050XW00 Whirlpool Automatic washer

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your washer. Upon researching model WFW9050XW00; it sounds like the machine control board may need to be replaced. The machine control board controls the cycles of the washer, so when it fails it can cause the washer no to go thru its cycles successfully. I have posted a link of the machine control board to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
April 16, 2015

Top Parts