Model #WDSR2080DAWW GE Residential Washers

  • Controls & Backsplash
    3 Results
  • Cabinet, Cover & Front Panel
    3 Results
  • Tub, Basket & Agitator
    3 Results
  • Suspension, Pump & Drive Components
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer will not spin closes on final rinse&spin or drain&spin WDSR2080DAWW Ge Washer

A:

Thank You for contacting ManageMyLife.com

I understand your frustration when your washer doesn't start the final spin. After researching your model, it sounds like the timer needs to be replaced. The timer is what triggers the washer to go into each cycle. If the washer is not completeting any spin cycles then your problem would be with the lid switch.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Timer for Model WDSR2080DAWW

Lid Switch for Model WDSR2080DAWW

If you have further questions please let me know.
Thanks for using ManageMyLife.com

 

Read More
Desirea -
Sears Technician
October 18, 2013
A:

Thank you. Got it running.

Read More
David -
October 19, 2013
See more answers
Q:

Standard Top Load Washer Won't Fill or Run

A:

I understand that you are having some trouble with your top loading washer not filling with water or running. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
April 05, 2013
A:

Thanks for the links but, the biggest problem I'm having is the tub won;t fill. It sounds like the machine wants to work but the water won't come in.

Read More
pfp -
April 05, 2013
A:

Thank you for your question.  I am sorry you are having a problem with your GE WDSR2080daww washer

Caution: Before attempting any repair, unplug the washer from the wall outlet. 

If the washer will not fill or run then I suspect the Timer is at fault.  The wiring diagram below may be helpful to you.  If a meter is available then the place to start is the Yellow/black wire on the water level switch. 

As long as the washer is plugged in there should be voltage on the YB wire. 

If no meter is available then you can have the problem repaired in your home by a Sears technician.  Here is the link: Sears Home Services Washer Repair

I hope this helps.  You can reply below with any additional details for further assistance. 

Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
April 06, 2013
A:

Thanks Fred. We think maybe, since we have really hard, "rusty" water that maybe the "silt" has blocked up the intake. We've ordered a new one which should be here on Tuesday. Hopefully, that's all that's wrong at this point since the washer is a little over 5 years old now.

Read More
pfp -
April 06, 2013
A:

Good luck with the valve.

Read More
Fred M -
Sears Technician
April 08, 2013
See more answers
Q:

GE washer water wont cut off and wash cycle will not start

A:

I am sorry that you are having some difficulties with your washer and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your washer troubles while you wait for your expert response.

Read More
Joseph P. -
September 13, 2012
A:

Thanks for your question about your GE washer overflowing water. I will be happy to assist you with this.
Having water overflowing is a frustrating occurrence, I am sure together we can find a solution. Based on you description of the problem I think there could be a problem with the pressure switch reading the water level. The pressure switch is the component on the control panel that you set the water level. This control can sometimes be reset by turning it all the way to the highest water level setting and beyond then back. Try this a couple times. Another check would be to remove the 1/4 inch tubing and attach another piece of tubing then with the water running in blow gently into the tube. If the water stops and the washer starts to wash the pressure switch should be good. And if it does not stop water and wash the pressure switch is defective. Part number wh12x10065. If the pressure switch test good then there must be a leak in the pressure tube that is attached to the switch.
This tube is attached to the bottom of the outer wash tub and supplies the air pressure to the pressure switch. Even the slightest pin-hole can cause the washer to malfunction and it will need to be replaced. The part number is wh41x365. I hope this helps resolve your problem. I will attach links for parts and service just in case. Should you need additional help please reply with details.

Thanks Ron H.
Sears PartsDirect . ,br> If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Ron H -
Sears Technician
September 14, 2012
A:

I intented to give this reply an 5 rating. Expert Ron H was 100% on the emoney. Your sugestion worked the switch reset just as you said. However if I had to checked the pressure hose ,are there quick connect to open the top of the washer? Thanks Expert Ron H

Read More
LLOYD -
September 16, 2012
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show