Model #WATER HEATER ELEMENT CROSS-REFERENCE GUIDE Water Heater Element

  • Cross Reference Stock# 3300000-3300210
    3 Results
  • Stock # Ap7483cl-ap8437nl
    3 Results
  • Stock # 239681-4 - 42285-14
    3 Results
  • Stock # 823617-1-238026-8
    3 Results
  • Stock # 9000092-9000155
    3 Results
  • Stock # 9000156-9000965
    3 Results
Find part by diagram >

Question and Answers

Q:

Dishwasher runs for 6 hours GLD5604V00WW Ge Dishwasher

A:

It can be very annoying and inconvenient when your dishwasher takes 6 hours to complete a washer cycle. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Your expert will answer within 24 to 48 hours with detailed information. Thank you for using Manage My Life.

Read More
Julio -
February 05, 2013
A:

Thank you for your question Joelle. I can see why you would be concerned about the dishwasher running so long. Please keep in mind that the regular cycle for the new energy efficient models is between 2 to 4 hours. There are a couple of thngs that can cause the cycle to run longer. One is if the water going to the dishwasher isn't hot enough. To test it, run the faucet closest to the dishwasher on hot for 2 minutes. Then hold a candy or meat thermometer in the water stream for 1 minute. Be careful as the water may be hot enough to burn. If it reads less than 120 degrees F, have a qualified person change the water heater setting.

If the tap water is okay, then the heater element may be failing. I have included the link to order the element.

Element for model GLD5604V00WW

I recommend running Dishwasher Magic thru it as detergent and mineral deposits can also slow the cleaning cycle. That link is:

Dishwasher Magic

Let me know if there is anything else I can do to help. And thank you for choosing Sears.

Read More
Rachel Morgan -
Sears Technician
February 05, 2013
A:

I've had this dishwasher for 2.5 years and it has never cleaned my dishes properly and now, it doesn't run past the first 90 seconds before it just shuts down. What do I do now? My last dishwasher, a Whirlpool was a war-horse and worked beautifully for 16 years. This GE product is a joke. What do you suggest since Sears obviously doesn't want to provide service and this product is a rip-off?

Read More
Kathleen -
November 27, 2015
See more answers
Q:

Water heater element wiring 153320590HT

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your water heater and I do understand your frustration. Glad to help out. I'm looking at your model number 153320590HT and the unit does require the 2 elements to be functioning in order for both to work. Due to the amount of water being heated the unit requires 2 elements. On 2-element tank, if upper element burns out, the lower element stops receiving electric power so neither element works and no hot water is available. Click here for information. I recommend contacting the original manufacturer (State Ind Water heaters) for rating information on the amperage. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 12, 2015
Q:

Kenmore Te code 79641172210 Kenmore Washer

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
I am sorry to hear of the issue you are experiencing with the Kenmore washer, I know how frustrating that is to have occur.
This will be a difficult issue to diagnose unless you have a multimeter and experience testing electrical components. 
The TE error indicates a water heating error detected. Check the water heater or element and the thermistor. The washer is reporting a fault on the heating circuit, it just can't tell you exactly where the fault lies. If you are comfortable using an ohm meter and making these kinds of tests, check the items below.

  1. Disconnect power to the dryer prior to any service or repairs.
  2. Check water heating element. Check wiring and connectors to water heating element.
  3. Check heater resistance with a multimeter. The resistance should be between 12-18 ohms. If it's not between those values, replace the heater assembly.
  4. The connector to the thermistor should be connected, is it disconnected or disassembled?
  5. Check the thermistor resistance. At ambient temperature around 86 degrees F, the resistance should be around 39.5 k ohms + or - 5%. The test points are between 1 to 2. If the resistance is not within that field, replace the thermistor.
  6. Also make sure the thermistor terminals are dry and free of any corrosion.

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-349-5071, or click here to be directed to the page to set up service.
Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business.

Read More
Jeff Wallace Sr -
Sears Technician
May 22, 2014