Model #W110 JENN-AIR Built-In Oven, Electric

  • Control Panel
    3 Results
  • Body
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers

Q:

Lamp size

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about the size of the lamp for your dryer. I am so sorry the information on the lamp cover and the information in the manual are conflicting. We will be happy to research this issue for you but will need some additional information. Please resubmit your question with the model number of the dryer included. You can normally find the model number on the facing of the dryer. It is hidden when the door is closed. 

Once we have the model number we will be happy to locate the lamp information for you. We look forward to your reposted question and the opportunity to resolve this question for you. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
February 07, 2015
A:

110.68942892 Thank you

Read More
Roger -
February 09, 2015
A:

the model number for this dryer is 110.68942892, as I stated before. I am still waiting for your answer as to the correct bulb. The plastic cover over the bulb on the dryer frame states 15 W, 110 v bulb only. the parts instruction manual calls for 25W 110 V bulb only. Please advise. Roger Wright

Read More
Roger -
February 11, 2015
See more answers
Q:

Dryer will not start!!!!! 11067902790 Kenmore Electric dryer

A:

A dryer is an appliance we depend on so much, when there's laundry to be done. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Yadira B -
January 23, 2013
A:

Thank you for your question and I understand your concern.

Based on your symptom and details I suspect it could have a faulty thermal fuse. The thermal fuse is connected in the motor circuit and when it opens/fails, the dryer will not start.

The thermal fuse #3390719 can be disconnected and then tested for continuity with an Ohm meter. The thermal fuse is located on the blower wheel housing. The thermal fuse will have two (2) blue wires connected to it. You will need to remove the front lower access panel to access the thermal fuse. To remove the lower access panel, disconnect the power cord from the power source first. Located above the access panel is two clips. Each one is about 4-6 inwards from each corner. You need to release the clips by inserting a putty knife directly in front of each clip and press it downwards and then pull out on that corner. Once the access panel has been taken off. The thermal fuse can be seen. I will add images in a second reply to reference.

NOTE: Disconnect the power cord from the power source before removing the lower access panel and thermal fuse.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 23, 2013
A:

Branden: I added a couple of images below to reference. I traced the motor circuit and circled the components that must be closed in order to complete the circuit to the motor. I circled the thermal fuse too. It is key #59 as shown below the wiring diagram. Be sure to disconnect the power cord from the power source before removing the lower access panel.

Read More
Joey S -
Sears Technician
January 23, 2013
See more answers
Q:

Why won't my Jenn-air oven model W110 heat?

A:

The wiring diagram for your oven is shown in the image below. In order to diagnose your failure, you would need to disconnect electrical power to the oven (shut off the breaker) and access the control console. Your symptoms point to a failed wire connection. Using the wiring diagram, you would need to check the connections on the thermostats and selector switches. It is likely that you will find a burned wire inside the control console. Repairing a failed wiring contact may repair the oven without having to replace a component. If the oven still will not work even though the wiring contacts are okay, then you would need to use the wiring diagram to check continuity though the switches (with electrical power disconnected) to determine the failed component. If you are not able to determine the failed component using the wiring diagram, I recommend calling a service technician to diagnose and repair the oven.

Read More
Lyle W -
Sears Technician