Model #V250 TEAC Tape Deck

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

Circuit for Kenmore Elite Dual Fuel Range

A:

I understand how important it is to have the correct part for your Range. While you are waiting on an expert to answer your question, a suggestion I have is to visit Sears Parts Direct website and speak with a Sears associate to find out what part is needed. I have attached the link below. Have a great day!

Read More
Dezeray S -
March 03, 2012
A:

Thank you for your question and I understand your concern.

A 30 amp circuit will be needed for your dual fuel range. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
March 05, 2012
A:

Thank you. The instructions weren't very clear, so I wanted to make sure.

Read More
John -
March 05, 2012
A:

I purchased this same range 790/41093100 and see the same tag for 21A in the broiler drawer. My concern is that they sent the plug to be installed as a 50Amp, 4 prong plug. My wife paid additional because they told her she would have to purchase the plug. On delivery, they wired the range with the new 50amp plug, but I only have 30amp dedicated service to it with 10 gauge wire. And if you read the specs online for this range, it says 40amp service. This is all very confusing. Please advise. Is 30 amp still ok?

Read More
Mike -
October 14, 2013
A:

Mike: It's okay to use a power cord that is rated higher in amperage than to use a power cord with a smaller amperage rating. The power cord recommended in the installation instructions is a 125v/250v 30 amp power cord. There is no problem with using a cord that can carry 50 amps you just do not want to use one that is too small and can't carry the amperage draw. Below is the URL to the installation instructions. You can copy and paste the URL in your browser to view or download the installation instructions. http://www.managemylife.com/mmh/lis_pdf/INSTL/1103525L.pdf

Read More
Joey S -
Sears Technician
October 15, 2013
See more answers
Q:

How do I remove the control panel to install a new control on my Kenmore range model 790.46572400?

A:

The image below shows the basic procedure for accessing the console on this type of range. Be sure that you shut off the breaker to disconnect electrical power before accessing internal components.

Read More
Lyle W -
Sears Technician
September 29, 2009
A:

Lyle and Barbara, Thank you for the advise the replacement switch went on smoothly. The only issue I have now is that the burner gets hot though it doesn't turn red hot like it did before. I know I have the right part, I made sure that I got a switch for an 8 inch burner size. Can you both think of. A reason that the burner does not get hot enough to turn red while the knob says "HI". Thank you again for your invaluable help! Marylynn

Read More
mary -
March 18, 2012
A:

You could have a problem with the element, the wiring or the terminal block (Key 27 on the parts drawing in the first image -- the connector that the element plugs into). Make sure that the element is plugged into that terminal block properly. If you find no problems there, I recommend that you SHUT OFF THE HOUSE CIRCUIT BREAKER for the range and lift the cook top as shown in the second image. Check the wiring connections on that terminal block. Check that terminal block for damage. If that terminal block is partially melted or shows signs of damage, then it will need to be replaced. You can order the parts that you need from this page: Kenmore Slide-In Range 790.46572400 Cook Top/Drawer Parts Page . I added a link for a repair video below that shows how to replace that terminal block on a similar range. Your range will not look exactly the same as the one shown in that video but the basic repair procedure is the same. Be sure that you SHUT OFF THE HOUSE CIRCUIT BREAKERS to completely disconnect electrical power to the range before accessing internal components. These tips may help you fix this current problem. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
March 19, 2012
A:

Thanks Lyle, The burner worked excellently prior to changing out The switch. Meaning, the burner got red Hot when on "HI". Without causing electrical problems, Can I change out the left rear 8in burner element with the Right front burner element safely? I want to see if The problem is actually coming from the burner element. When changing out the switch, I did notice the replacement Switch had 240v on it, the old one had 250v. Could This be why the burner is not getting red hot, not equivalent Volts? As always thanks for your expert advice! Marylynn

Read More
mary -
March 19, 2012
A:

That voltage rating label should not affect the burner output if you installed the correct burner switch. You can unplug the range and switch those burners to see if that element is okay. Those elements and the terminal blocks are identical. If that burner works properly in the other position then the element is apparently okay. In that situation, I recommend that you UNPLUG the range and check that wiring on the burner switch. Check the wiring between the burner switch and the terminal block. Check the part number on that burner switch that you just installed. The part number for that burner switch should be 903136-9020. If you see a different part number on that switch, reply with that part number and I will check it for compatibility. If you installed part 903136-9020 and the element will not heat properly in that position then you could have a bad switch, a wiring failure or a bad terminal block on that burner.

Read More
Lyle W -
Sears Technician
March 19, 2012
A:

Yes, I have the right part number, although I am using a substitute 318220080. I did exchange the burner coils out. That checked out. The burner with the new switch takes 13 min to boil a little over 3 cups of cold water because it does not get red hot on the "HI" setting. My next question is: can I switch out the new switch that is on the right front, to the other large burner on the left rear? This way, I will still be able to cook closer to the front with a red hot burner and leave the burner with the new switch in the back on the side I really don't use a lot Thanks again for your advice!

Read More
mary -
March 20, 2012
A:

That part 318220080 appears to be a burner switch for a small burner. Your details indicate that you are replacing the switch for a large burner. It is likely that the burner switch is causing your problems. You can UNPLUG the range and swap those switches but you will probably find out that the large burner switch will work properly. I recommend that you order and replace that burner switch for the large burner using part 903136-9020. Here is a direct link for that part: Large Element Burner Switch for Kenmore Range 790.46572400 . Be sure that you UNPLUG the range before accessing and replacing that burner switch. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
March 21, 2012
A:

Lyle, Thank you ! I was able to exchange the switch, which turned out to be for a small burner,mfor the correct size. Now I have a re hot burner, with a new switch! You saved me at least 100$. Thank you again for your help.

Read More
mary -
March 21, 2012
A:

Thanks for letting us know how this turned out. We are glad to hear that the burner is working properly. Let us know if you ever need more help.

Read More
Lyle W -
Sears Technician
March 21, 2012
See more answers
Q:

Can I use a standard 125/250v 3-wire clothes dryer power cord if the manual states to use a 120/240v?

A:

The 3 wire power cord rated at 125/250 volt, 30 amp is perfect for you application and is pretty much a standard rating for dryer power cords. It's safe to use a power cord that has a higher voltage/amperage rating rather than a power cord with too small of voltage/amperage rating.

Using a power cord with a volt/amperage rating lower than what's recommended is not safe or recommended.

It will not harm your dryer by any means. It's perfectly OK to use the 125v/250v 30 amp power cords on your electric dryer.

Read More
Joey S -
Sears Technician
August 25, 2008