Model #TEDS740PQ0 ESTATE Residential Dryer

  • Cabinet Parts
    3 Results
  • Top And Console Parts
    3 Results
  • Bulkhead Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

How many CU FT is my Estate by Whirlpool Washer and Dryer set? TAWS750PQ0 Estate Residential washer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the capacity of your washer and dryer. 

I do apologize the manufacture no longer gives us the capacity of your washer and dryer due to the age of the product.  You would need to measure the unit yourself in order to determine the cubic feet.

This is a geometric method to calculate tub capacity based on the cylinder volume formula. Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.

 

Why? Because the tub is not exactly a cylinder. The edge where bottom connected to the wall is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.

 

This method can be used as a crude estimate but we do not recommend using it for comparisson when shopping for a new washer.

 

Determine your washer tub capacity by taking two simple measurements:

 

 

 

1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)

 

2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some tubs are narrow on top. In this case make the measurements INSIDE the tub.

 

Solution:

 

 

Tub Depth:  in.   Tub Diameter:  in. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

 

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
June 02, 2015
Q:

Whirlpool Estate Dryer mdl TEDS740PQ0 tripping circuit breaker

A:

With the dryer not working properly in your home can be quite concerning. I have taken the time to research on the website and have locate similar information towards your issue. While you are waiting for a detailed reply from an expert I have attached the links below. If you do decide to have a technician diagnose and make repairs, an option is to visit Sears Home Services and use the handy scheduler,which I have also provided the link below. Hope this helps!

Read More
Priscilla V -
March 14, 2012
A:

From the description you give I suspect the problem is with the element even though it worked well for 6 months after you replaced it. You may need to visually inspect the coil to make sure it is not broken. The problem can also be with the circuit breakers themselves. Sometimes the circuit breakers are weak and trip drawing less amperes than their rated for. You would need a meter to check the amp draw. While running and heating the dryer can draw between 24 and 28 amperes. The breakers should be rated for at least 30 amperes. I'd suggest checking the element first. You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
March 14, 2012
A:
Parts Expert -
March 14, 2012
A:

Thanks Fred M...The heating element is working....if the coil was "broken" wouldn't that break the cycle and stop it from heating at all? The breakers (which ARE 30 amp) may be bad, but seem to be doing the intended purpose and "breaking" when the amp draw is too great and operating correctly without the heat cycle on, so I suspect the problem is in the heat cycle rather than the breakers. Where would I test with my multimeter to determine which element in the heating cycle circuit is bad?

Read More
Steve -
March 14, 2012
A:

The black wire on the terminal block would be the best wire to put the clamp around. This will give you the amp draw of the motor and element. It is possible for the element to be broken yet still heat. At some point the heat would cause the wires to separate and if ones heats the heating housing then breaker will trip. Remember to unplug the dryer before putting the meter in position.

Read More
Fred M -
Sears Technician
March 17, 2012
See more answers

Top Parts