Model #TAWX700JQ1 ESTATE Residential Washers

  • Top And Cabinet/literature
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Miscellaneous/optional
    3 Results
Find part by diagram >

Question and Answers

Q:

size / capacity TAWX700JQ1 Estate Washer

A:

Thank you for choosing Sears Parts Direct. I can certainly assist you in locating the cubic geet for your washer. I did look into the model number you have provided and I do apologize do to the age of the unit we do not have the cubic feet size. After 5-10 years the manufactures stops giving information to certain parts. 

You will need to measure the unit to determine what size you unit need.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

Thank you for your question. Have a great day

Read More
Natasha12 -
Sears Technician
June 30, 2014
Q:

Why doesn't my Estate washer drain all the water?

A:

Water being left at the bottom of the washer sounds like a hassle and can build up a smell. I am adding a link below to help you with your question while you wait for your expert response.

Read More
Joseph P. -
February 08, 2012
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating it is to have a problem with a washer. We are here to help. I suspect the washer has a restriction in the pump or drain line. There may be a sock stuck in the bottom of the tub slowing down the water flow. Here the instructions on how to fix the problem. The sock may be stuck in the washtub but not to the drain hole, the spin basket has to be removed. To do this the cabinet of the washer has to be removed. First, unplug the washer. Remove the screw in the back of end cap and flip control panel over. It should look like the third image. Then remove the splash ring on the top of the tub. It just clips on. If the sock is close to the side of the spin basket, you might be able to fish it out with a metal coat hanger. If not, you have to remove the agitator next. Remove the softener dispenser and the cap under it. You should see a square hole. Place a half-inch extension in the hole and turn it counter clockwise. Once loose, you can lift the top portion of the agitator out. Next, remove the stud and take the lower portion out. Now you should see the spanner nut that secures the spin basket. This nut should be removed with a spanner wrench. If you do not have a wrench, I have seen the nut removed with a large pair of channel lock pliers or a hammer and punch. This will work but you have to make sure to get the nut tight when you reassemble the washer. Once the nut is removed, you and lift the spin basket out and retrieve the sock. After removing the sock, reassemble the washer in the reverse order. If the sock is in the pump are remove the hoses to the pump and pull the sock out. If you need to order the spanner wrench, type in Whirlpool spanner nut wrench on Google. It will cost around 20 dollars.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. You may visit SearsHomeServices.com and click on the red Start now button.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
February 09, 2012
See more answers
Q:

estate whirlpool washer

A:

It can be difficult to adjust without a washer or dryer. While your waiting for an expert to respond you could I attached some links below that will give a detailed answer about your issue. I hope this helps!

Read More
Jackie S -
July 21, 2011
A:

Thank you for your question.

By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the two colored wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

Please click here to watch a video on how to replace the lid switch.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
July 22, 2011
See more answers

Top Parts