Model #SYSTEMS 50 HARRIS SYSTEMS INC. Welder

  • Rectifier Mounting Kit
    3 Results
  • Transformer Mounting Plate Rh
    3 Results
  • Internal Mounting Plate-upper
    3 Results
  • Choke
    3 Results
  • Mk1 Machine Cutting Torch
    3 Results
  • Top Cover And Key/tool
    3 Results
  • Mk1 Hand Cutting Torch
    3 Results
  • Uniplug Body
    3 Results
  • Hand Torch
    3 Results
  • Machine Torch
    3 Results
  • Switch Piston Assembly
    3 Results
  • Auxiliary Transformer
    3 Results
  • High Frequency Unit
    3 Results
  • Base Assembly
    3 Results
  • Rectifier And Solenoid
    3 Results
  • Microfine Filter Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

transformer & monitor problem 831159231 Lifestyler Lifestyler system 50ers

A:

I’m looking at a weight system for the model 831.159231 that was provided. Looking into this I don’t see anything as far as a transformer, or monitor. Maybe check the model number again and make sure it’s all correct.

Read More
JeffwallaceIII -
Sears Technician
July 17, 2015
Q:

Craftsman Rock Cutting Machine?

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Yadira B -
October 31, 2012
A:

I added a photo in a separate post from my original question.

Read More
Michael -
October 31, 2012
A:

Thank you for your question on the lapidary Craftsman tool.

Without a model number I cannot access any information that may be available.

I did find some information on the web but I do not have a category in the system any longer for this type of equipment.

Can you send me a picture of the tool?

Sam A.

Read More
Sam A -
Sears Technician
November 01, 2012
A:

Thanks for your response re the "lapidary" Craftsman tool. I posted a picture on 10/12/12 (shown just above your response). Please let me know if you cannot access the photo and I will re-post.

Read More
Michael -
November 01, 2012
A:

Thank you for the picture of the Craftsman wet bowl lapidary stone shaping tool. I got the picture know. I had a friend of mine in Houston that had one like that and he use it for faceting the stones with an abrasive wet wheel in one like this. I have looked all over to find any information on this tool and I think it is so old that the category is no longer available in out reference system. I this it may be from the 50's or 60's. I am sorry that I could not help you with information on this lapidary tool. Sam A.

Read More
Sam A -
Sears Technician
November 01, 2012
A:

Thank you for your help. I would like to try to put this in the hands of someone who may use it. Would your friend be interested in it? or too much trouble to ship from L.A. area?

Read More
Michael -
November 01, 2012
A:

Thank you for the update. I have not talked to him in 15 years. We were work friends and I move away to the Austin area and he retired because he was older than me and I am not sure he is still alive because he retired for health reasons. He use to have it on his back covered patio and he made beautiful cut gems. I am sure that there is a lapidary club in your area because he belonged to one in Houston. Look for a rock and gem show in your area where they all sell and interchange materials. Sam A.

Read More
Sam A -
Sears Technician
November 01, 2012
A:

Good idea. I will look in the Los Angeles area. On a side note, I periodically go to Dripping Springs and Harper to visit relatives. Take care.

Read More
Michael -
November 01, 2012
A:

I am sure you will find a club or rock and gem show in the LA area. Be well my friend. Sam A.

Read More
Sam A -
Sears Technician
November 01, 2012
See more answers
Q:

maytag msd264rhew flood

A:

I can understand your concern over your Maytag side by side leaking water. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
September 08, 2012
A:

Based on the amount of water that was leaking, it is likely that you have a bad water valve assembly for that ice maker. The valve could be allowing water to leak into that ice maker mold to the point that it is overflowing. Shutting off the water supply to the refrigerator will stop that type of leak until you can get the problem fixed. I suspect that you may have already shut off the water supply.

You can shut off the ice maker by lifting the metal bail arm to the "up" position. Briefly restore the water supply and see if the ice mold in the ice maker begins to fill with water. If it does, then you may need to replace the water valve assembly. I recommend that you have a service technician verify that failure and perform the repair. Here is a link for the Sears Service website: Sears Home Services .

If you want to diagnose and repair this problem yourself, reply with additional details and we will assist you further.

This is not a common problem on that model of refrigerator. That being said, a component failure can occur at any time. Once you get that problem fixed, you will probably not have further problems. The amount of humidity will not affect the water system and ice maker. It can affect the automatic defrost system but the 50% humidity should not be a major factor.

Read More
Lyle W -
Sears Technician
September 11, 2012
See more answers