Model #SVE47500W JENN-AIR Slide-In Range, Electric

  • Control Panel
    3 Results
  • Top Assembly
    3 Results
  • Oven
    3 Results
  • Door
    3 Results
  • Blower Assembly (plenum)
    3 Results
  • Access Panel
    3 Results
  • Body
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

Which cartridge? sve 47500 w

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about a part for your Jenn Air cooktop model SVE47500W.  I will be happy to help you with this. I have included the link below for your to view and order the part.

Click Here

The part number JEA7000AA will fit your model. It is the substituted part for the original cartridge number A100W which is no longer made. It may look a little different, but is guaranteed to fit.

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
April 25, 2015
Q:

I would like to get the schematics for my Jenn-air Convection Oven Model #SVE47500W so we can fix the Omh sensor.

A:

When it comes to working on repairing your range it is always important on have all proper schematics to your model. While you are waiting for a detailed reply from an expert I recommend visiting the Sears parts direct website were you can view a full parts list and diagram of your model. I have provided the link below. Hope this helps!

Read More
Priscilla V -
December 26, 2012
A:

I see that Priscilla V. posted a link for the parts diagram on that range in the above response. That will help you see the components of the range. I added some image below that show the basic disassembly procedures for that range. Be sure that you shut off the house circuit breakers for the range before accessing internal components and replacing parts. That may further help you access and replace the wire harness for the oven temperature sensor probe. Note: If you can determine the location of the wiring harness failure in that oven temperature sensor circuit, then you may be able to fix that problem without tearing down the entire range to replace that entire harness. The failure in the wire harness often occurs in the disconnect plug at the sensor probe itself. You can check the continuity through that disconnect plug. If that plug is bad and the rest of the harness is okay, then you can carefully cut that plug out of the harness and connect the wires going to that sensor probe using ceramic wire nuts. That tip may save you some time and money if the disconnect plug is bad.

If you need more help, reply with additional details.

If you get to the point where you need to have a service technician replace that wire harness, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 26, 2012
See more answers
Q:

Jenn air SVE47500, Bake,grill and top grill module will not work. no display for the two functions. Control pad replaced with new one, no change.

A:

It is disappointing when a major appliance starts to malfunction. I was unable to locate information that will be helpful. An expert will respond within 24-48 hours. I hope your issue gets resolved.

Read More
Jackie S -
January 19, 2012
A:

I do not have an internal component diagram for that clock control board on the range. I provided a general wiring schematic and a wiring diagram for this range in the images below. You can use this information to check the continuity of wiring and the voltage supply going to the control board (you may have already done that). NOTE: Follow electrical safety guidelines when accessing and checking internal range components. Completely disconnect the electrical power supply when accessing internal components. When conducting live voltage testing, wear proper safety equipment -- insulated rubber electrical safety gloves and safety goggles . From your details, I suspect that you already know and follow these guidelines. If that control is getting electrical power but will not power up the display, then it will probably need to be replaced unless you can find the cause of that failure on your own without internal component schematics for the circuit board. The problem with the grill not heating can probably be diagnosed using the information shown below. You can disconnect electrical power and check the continuity through the burner switch and the wiring. If the switch is bad, it will need to be replaced.

You can order parts from the Sears PartsDirect.com website. Disconnect electrical power from the range before accessing and replacing internal components.

If you need more help, reply with additional details and we will assist you further.

In the unlikely event that you get to a point where you need to have a service technician examine and repair the range, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 21, 2012
See more answers

Top Parts