Model #SVE47100W JENN-AIR Slide-In Range, Electric

  • Control Panel
    3 Results
  • Top Assembly
    3 Results
  • Body
    3 Results
  • Oven
    3 Results
  • Door
    3 Results
  • Access Panel
    3 Results
  • Blower Assembly (plenum)
    3 Results
  • Wiring Information (sve47100b/w)
    3 Results
  • Wiring Information (sve47100bc/wc)
    3 Results
  • Wiring Information (sve47100b/w-ser 15)
    3 Results
  • Wiring Information(sve47100bc/wc Ser 14)
    3 Results
Find part by diagram >

Question and Answers

Q:

Jenn Air model #SVE47100W, Display is not legible after cooking. Need advice or help SVE47100W Jenn-air Electric slide-in range

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

 

Read More
Joseph P. -
July 10, 2013
A:

Thank you for choosing SearsPartsDirect.com. I understand how important it is to be able to see the display panel on your oven. I have included images below to show you how to run a diagnostic test on your oven. Once you have an error code, we can better find out what could be happening to the display.
If you do not get an error code, I recommend having your board tested for proper voltage supply. An ohmeter is normally needed for this test. I have included instructions below on how to install a new board if needed.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Turn off the range breaker in your service panel.

2. Open the oven door and remove the screws under the control panel, securing the control housing to the range. Pull the control housing away from the range. Be sure to not pull the wires off the control housing components.

3. Remove the screws securing the control panel to the control housing, then remove the control panel.

4. Install the new control panel using the screws that were removed from the old control panel.

5. Transfer the wires from the old control panel to the new control panel. Transfer the wires one at a time to ensure they are installed into the correct terminals.

6. Align the control housing and re-secure the screws to the underside to hold it in place.

7. Restore power to the range to complete the repair.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using SearsPartsDirect.com.

Read More
Desirea -
Sears Technician
July 11, 2013
See more answers
Q:

Jenn-Air Electric Oven sve47100w Bake Element Not Working

A:

The problem with the bake element is concerning. I found some information for you that I am hoping will help you with the oven. I am adding the link below to help you with your question while you wait for your expert response. It may take 24-48 hours. I do hope that everything works out on the range.

Read More
Marc -
November 14, 2012
A:

Check to see if the broil element is working. Check to see if the stove top elements heat. If none of the elements in the range are heating then you may have a voltage supply problem. Check the house circuit breakers or house fuses for the range in that situation.

Since you did not mention a problem with the stove top burners, I assume that they are working. If the broil element does not work and the serial number on your range is 14 or higher, then you could have a problem with the high limit safety thermostat for the oven elements. A failed electronic oven control board could also prevent the oven elements from heating. On that model of range with a serial number that begins with 10 through 13 as the first 2 digits, you could have a bad electronic oven control board or a wiring failure that is causing that problem. If the broil element heats, then you probably have a bad electronic oven control board causing this problem. A shorted out bake element in the oven will often damage the electronic control board. Replacing that component may fix your problem.

There are differences in the specific versions of this model of range based on the serial number. The first 2 digits of that serial number determines the "Series" number. I recommend that you reply to the thread with that serial number if you want to fix this problem yourself. We can help you further with troubleshooting and parts information once we have that additional information.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 16, 2012
A:

Thank you for replying! Everything works on the oven, including the stove top and broil elements EXCEPT for the bake element. The bake element is the only thing that is not working. The serial # of the oven is: 1418049150. The manual also suggests that the problem may be with the control board, unfortunately all signs indicate that the company no longer makes this part. If you still think this is the problem,and know where I can find a new control board please let me know!

Read More
Jen64 -
November 16, 2012
See more answers
Q:

Jen Air model sve47100W, s/n 20861439wm - oven flashes F9

A:

I understand that your oven is flashing the F9 error code. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful. Have a nice day.

Read More
Alina F. -
August 05, 2011
A:

This was not helpful at all because it is for a different range, mine is not a door lock issue but a oven not working issue. Mine is not a Kenmore but a Jen Air .

Read More
jeanette hardy -
August 05, 2011
A:

I provided technical information for that Jenn-Air range in the images below. That F-9 code does indicate that the control board detects a problem with the oven door lock circuit. The information shown below should help you check that circuit using the test program for the control. You could have a bad control board in the console or a problem with the switches. A wiring failure or corrosion on the wire harness contacts could cause this failure. Be sure that you shut off the house circuit breaker for the range to disconnect electrical power before accessing internal components. If you need more help, reply with additional details based on the technical information provided below.

If needed, you can order parts from the Sears PartsDirect website.

This type of range can difficult to diagnose and repair. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 08, 2011
See more answers

Top Parts