Model #RGB532BEA2AD HOTPOINT Free Standing, Gas

  • Gas & Burner Parts
    3 Results
  • Control Panel & Cooktop
    3 Results
  • Body Parts
    3 Results
  • Door & Drawer Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

oven not heating RGB532BEA2AD Hotpoint Gas range

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

That glow bar igniter may still be bad. It is very likely that the glow bar igniter could glow and still be bad; it just won’t glow hot enough to ignite the gas. I recommend in replacing that glow bar.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
Samantha A -
Sears Technician
December 05, 2014
Q:

i have a ge hot point stove and the oven wont light but igniter lights ups my modole no is rgb532bea2ad

A:

It can be very difficult to deal with a oven that isn't properly working, repairing can be expensive. Below I attached a link that will help explain your issue. I hope this helps!

Read More
Jackie S -
July 29, 2011
A:

Check the oven gas supply shut-off on the regulator as shown in the image below. Be sure that you unplug the range before accessing internal components. Since your details indicate that the igniter glows, then the thermostat and safety gas valve are probably okay. The image below shows the theory of operation for the gas burner in this range. Your likely failure is the igniter even though it is glowing. It is likely too weak and the resistance through that component is not decreasing to the point where the appropriate current is flowing through the circuit to the gas valve. Replacing that igniter will likely fix your problem based on your description of the failure. You can order parts from the Sears PartsDirect website. The procedure for replacing the igniter is shown in the image below. Be sure that you unplug the range before accessing internal components.

If you need more help, reply with additional details based on the information provided below.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 01, 2011
A:

This has definitely helped, but my new igniter is not coming on, the broiler igniter works, could it be that it is not getting enough voltage?

Read More
Brian -
September 09, 2011
A:

If the original igniter was glowing, then the new igniter should also be glowing in that bake cycle. I recommend that you UNPLUG the range and check the wiring connections. There is a chance that you have a bad thermostat or a failed safety gas valve but that type of failure would normally have been exhibited by the original igniter not glowing. You can check the continuity through that thermostat and the safety gas valve with the range still UNPLUGGED. The safety gas valve should measure about 1.5 ohms of resistance. The thermostat should measure near zero ohms of resistance when it is in the "on" position. I hope that this additional information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
September 09, 2011
A:

The original igniter was not glowing, thats why if thought it was going to be an easy fix, just replace the igniter. Now not so easy, I will check the ohms. Thanks for your help so far.

Read More
Brian -
September 09, 2011
A:

Quick question, would i get continuity through the new igniter?

Read More
Brian -
September 09, 2011
A:

Yes. You should measure continuity through the new igniter.

Read More
Lyle W -
Sears Technician
September 12, 2011
See more answers

Top Parts